Delta 11-990C User Manual

Browse online or download User Manual for Tools Delta 11-990C. Delta 11-990C User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 16
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
INSTRUCTION MANUAL
12" Bench Drill Press
(Model 11-990C)
PART NO. 1234956 (011)
Copyright © 2001 Delta Machinery
Français au verso
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-GO-DELTA (463-3582).
Page view 0
1 2 3 4 5 6 ... 15 16

Summary of Contents

Page 1 - 12" Bench Drill Press

INSTRUCTION MANUAL12" Bench Drill Press(Model 11-990C)PART NO. 1234956 (011)Copyright © 2001 Delta MachineryFrançais au versoTo learn more about

Page 2 - SAFETY RULES

10EXTENSION CORDSUse proper extension cords. Make sure your extensioncord is in good condition and is a 3-wire extension cordwhich has a 3-prong groun

Page 3 - FOR DRILL PRESSES

11TABLE ADJUSTMENTS1. The table can be raised or lowered on the drill presscolumn by loosening the table clamp handle (A) Fig. 23,and turning the tabl

Page 4 - UNPACKING AND CLEANING

12SPINDLE SPEEDSFive spindle speeds of 620, 1100, 1720, 2340 and 3100RPM are available. The highest speed is obtained whenthe belt is on the largest s

Page 5 - ASSEMBLY

13ADJUSTING SPINDLERETURN SPRINGThe spindle is automatically returned to its upper mostposition upon release of the handle. It is recommendedthat the

Page 6

14BORING IN WOODTwist drills, although intended for metal drilling, may also be used for boring holes in wood. However, machine spur bitsare generally

Page 7

15NOTES

Page 8 - SUPPORTING SURFACE

16PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a network of

Page 9 - GROUNDING INSTRUCTIONS

2SAFETY RULESWoodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain hazards in

Page 10 - MINIMUM GAUGE EXTENSION CORD

31. DO NOT operate your tool until it is completelyassembled and installed according to the instructions.2. IF YOU ARE NOT thoroughly familiar with th

Page 11 - TABLE ADJUSTMENTS

4UNPACKING AND CLEANINGYour drill press is shipped complete in one container. Carefully unpack the drill press and all loose items from thecontainer.

Page 12 - DRILLING HOLES TO DEPTH

5ASSEMBLY1. Assemble the column (A) Fig. 3, to the base (B) usingthe four screws (C), three of which are shown. Loosenset screw (D) and remove ring (E

Page 13 - RETURN SPRING

64. Slide raising rack (F) Fig. 7, table and table bracketonto drill press column, as shown. Make sure bottom ofraising rack (F) Fig. 8, is engaged wi

Page 14 - ACCESSORIES

77. Figure 11, illustrates the table raising and loweringhandle (K) assembled to worm gear shaft (G).8. Thread clamp handle (M) Fig. 12, into hole in

Page 15

811. IMPORTANT: Make certain the spindle taper (Q) Fig.15, and tapered hole in chuck (R) are clean and free ofany grease, lacquer or rust preventive c

Page 16 - Two Year Limited Warranty

9CONNECTING TOOL TO POWER SOURCEPOWER CONNECTIONSA separate electrical circuit should be used for your tools. This circuit should not be less than #12

Comments to this Manuals

No comments