Delta 302 Owner's Manual Page 7
- Page / 44
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
OM-223 Page 3
1-3. Additional Symbols For Installation, Operation, And Maintenance
FIRE OR EXPLOSION hazard.
Do not install or place unit on, over, or near
combustible surfaces.
Do not install unit near flammables.
Do not overload building wiring − be sure power supply system is
properly sized, rated, and protected to handle this unit.
FALLING EQUIPMENT can injure.
Use lifting eye to lift unit only, NOT running
gear, gas cylinders, or any other accessories.
Use equipment of adequate capacity to lift and
support unit.
If using lift forks to move unit, be sure forks are long enough to
extend beyond opposite side of unit.
Keep equipment (cables and cords) away from moving vehicles
when working from an aerial location.
Follow the guidelines in the Applications Manual for the Revised
NIOSH Lifting Equation (Publication No. 94−110) when manu-
ally lifting heavy parts or equipment.
OVERUSE can cause OVERHEATING
Allow cooling period; follow rated duty cycle.
Reduce current or reduce duty cycle before
starting to weld again.
Do not block or filter airflow to unit.
FLYING SPARKS can injure.
Wear a face shield to protect eyes and face.
Shape tungsten electrode only on grinder with
proper guards in a safe location wearing proper
face, hand, and body protection.
Sparks can cause fires — keep flammables away.
STATIC (ESD) can damage PC boards.
Put on grounded wrist strap BEFORE handling
boards or parts.
Use proper static-proof bags and boxes to
store, move, or ship PC boards.
MOVING PARTS can injure.
Keep away from moving parts.
Keep away from pinch points such as drive
rolls.
WELDING WIRE can injure.
Do not press gun trigger until instructed to do
so.
Do not point gun toward any part of the body,
other people, or any metal when threading
welding wire.
MOVING PARTS can injure.
Keep away from moving parts such as fans.
Keep all doors, panels, covers, and guards
closed and securely in place.
Have only qualified persons remove doors, panels, covers, or
guards for maintenance and troubleshooting as necessary.
Reinstall doors, panels, covers, or guards when maintenance is
finished and before reconnecting input power.
READ INSTRUCTIONS.
Read and follow all labels and the Owner’s
Manual carefully before installing, operating, or
servicing unit. Read the safety information at
the beginning of the manual and in each
section.
Use only genuine replacement parts from the manufacturer.
Perform maintenance and service according to the Owner’s
Manuals, industry standards, and national, state, and local
codes.
H.F. RADIATION can cause interference.
High-frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communications equipment.
Have only qualified persons familiar with
electronic equipment perform this installation.
The user is responsible for having a qualified electrician prompt-
ly correct any interference problem resulting from the installa-
tion.
If notified by the FCC about interference, stop using the
equipment at once.
Have the installation regularly checked and maintained.
Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
ARC WELDING can cause interference.
Electromagnetic energy can interfere with
sensitive electronic equipment such as
computers and computer-driven equipment
such as robots.
Be sure all equipment in the welding area is
electromagnetically compatible.
To reduce possible interference, keep weld cables as short as
possible, close together, and down low, such as on the floor.
Locate welding operation 100 meters from any sensitive elec-
tronic equipment.
Be sure this welding machine is installed and grounded
according to this manual.
If interference still occurs, the user must take extra measures
such as moving the welding machine, using shielded cables,
using line filters, or shielding the work area.
- Deltaweld Series 1
- From Miller to You 2
- TABLE OF CONTENTS 3
- DECLARATION OF CONFORMITY 4
- 1-1. Symbol Usage 5
- 1-2. Arc Welding Hazards 5
- NOISE can damage hearing 6
- 1-6. EMF Information 8
- 2-1. Symboles utilisés 9
- OM-223 Page 10 14
- SECTION 3 − DEFINITIONS 15
- 3-2. Input Connection Label 16
- 3-4. Nameplate Safety Symbols 16
- 3-5. Symbols And Definitions 17
- SECTION 4 − INSTALLATION 18
- 4-5. Volt-Ampere Curves 19
- 4-6. Selecting A Location 20
- 4-7. Dimensions And Weights 21
- 4-8. Tipping 21
- 4-10. Weld Output Terminals 22
- ! Turn off power be 23
- ! Do not use worn 23
- ! Turn off power before con 24
- Work like a Pro! 25
- 4-16. Placing Jumper Links 27
- 4-17. Connecting Input Power 28
- IMPORTANT 28
- SECTION 5 − OPERATION 29
- 6-1. Routine Maintenance 30
- 6-2. Fuse F1 30
- 6-3. Short Circuit Shutdown 30
- 6-4. Troubleshooting Table 31
- Figure 7-1. Circuit Diagram 32
- OM-223 Page 29 33
- SECTION 8 − PARTS LIST 34
- OM-223 Page 31 35
- OM-223 Page 32 36
- Hardware is common and not 37
- OM-223 Page 34 38
- Hardware is common and 40
- Effective January 1, 2010 43
- For Service 44
- Owner’s Record 44
Related products and manuals for Welding System Delta 302
(20 pages)© 2020, manymanuals.com. All rights reserved. | 1.371 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals