Delta 36-865 Instruction Manual

Browse online or download Instruction Manual for Welding System Delta 36-865. Delta 36-865 Instruction manual User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 20
  • Table of contents
  • BOOKMARKS
  • Rated4.5 / 5. Based on18 customer reviews
Page view 0
INSTRUCTION MANUAL
PART NO. 1348009 - 03-31-05
Copyright © 2005 Delta Machinery
VERSA-FEEDER
TM
(Model 36-865)
Stock Feeder
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
Page view 0
1 2 3 4 5 6 ... 19 20

Summary of Contents

Page 1 - VERSA-FEEDER

INSTRUCTION MANUALPART NO. 1348009 - 03-31-05Copyright © 2005 Delta MachineryVERSA-FEEDERTM(Model 36-865)Stock Feeder To learn more about DELTA MACHIN

Page 2 - TABLE OF CONTENTS

102. Place the pivot ball housing (F) Fig. 7 in the sleeve (G) of stock feeder.NOTE: Position the slot in the pivot ball housing (F) "up" (F

Page 3 - CALIFORNIA PROPOSITION 65

115. Insert the metal shaft (J) Fig. 12 through the hole in the side of the sleeve (G) and into the wide slots of the pivotcover (H) Fig. 12. Thread t

Page 4 - GENERAL SAFETY RULES

129. Insert the end of the overarm assembly (B) Fig. 18 into the clamp assembly (M) until the gear inside the clampassembly meshes with the rack on th

Page 5 - SAVE THESE INSTRUCTIONS

13ALTERNATE ASSEMBLY ARRANGEMENTTo assemble the Versa-FeederTMin the mounting arrangement shown in Fig. 4, attaching the pivot ball to the overarmclam

Page 6 - GROUNDING INSTRUCTIONS

146. Insert the straight end of the overarm (A) Fig. 29 through the housing (E). Attach the pivot ball (F) Fig. 29 to the over-arm (A) with a 3/8-16 x

Page 7 - CARTON CONTENTS

15MOUNTING THE VERSA-FEEDERTM TO A MACHINE TABLEDecide on the location you wish to mount the Versa-FeederTMon your machine. Refer to Figs. 44, 45, and

Page 8

16Variable speeds from 10 FPM to 46 FPM are availablewith the stock feeder. To change the feed rates, rotatethe knob (A) Fig. 39 until the desired fee

Page 9 - ASSEMBLY

17REPLACING FEED ROLLERSEach feed roller is removable for repair or replacement. To remove the feed rollers:1. Loosen the three screws (A) Fig. 42 and

Page 10

18TROUBLESHOOTINGFor assistance with your machine, visit our website at www.deltamachinery.comfor a list of service centers or callthe DELTA Machinery

Page 11

19PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof P

Page 12

2TABLE OF CONTENTSRead and understand all warnings and operating instructions before using any tool or equipment. Whenusing tools or equipment, basic

Page 13

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marquessuivantes sont de

Page 14

3Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

Page 15 - OPERATION

4GENERAL SAFETY RULESREAD AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFOREUSING THIS EQUIPMENT. Failure to follow all instructions listed

Page 16 - MACHINE USE

5FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.ADDITIONAL SPECIFIC SAFETY RULESSAVE THESE INSTRUCTIONS. Refer to them often and

Page 17 - REPLACING FEED ROLLERS

6A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

Page 18 - MAINTENANCE

7FOREWORDDelta Model 36-865 Versa-Feeder Stock Feeder (Variable Speed) includes a 1/8 hp 120V reversing motor. This modelcomes with three rubber feed

Page 19 - WARRANTY

81. Stock Feeder2. Overarm3. Overarm Clamp Assembly4. Swivel Joint5. Base6. Pivot Ball7. Shaft8. 14MM and 17MM Open-end Wrench9. T-Handle Screw10. Loc

Page 20 - • DELTA)

9ASSEMBLYASSEMBLY TOOLS REQUIREDASSEMBLY TIME ESTIMATE3/8" Wrench5/16" Wrench7/16" Wrench1/2" Wrench4mm Hex WrenchPhillips Screwdr

Comments to this Manuals

No comments