QUICK S TA R T
1. Fold out legs
2. Mount saw parallel to beam
3. Align work supports with saw table
4. Align roller fences with saw fence
5. Extend arm
6. Cut wood
Lock
towards
“tighten”
position
Slide at
“unlock”
position
1
2
3
4
5
Tools needed
• 1/2” open-end wrench
• Socket wrench with 1/2” socket
• 3/8” open-end wrench
• Flat-head screwdriver - medium tip
• 7/8 open-end wrench
• 7/16 open-end wrench
• 5/32 allen wrench
• 9/16 hex wrench
• 3/16 allen wrench
1 INSTRUCTION MANUAL
UNIVERSAL WORKSTATION
TracRac Inc. 994 Jefferson Street, Fall River, MA 02721-4893 • 508-677-4130
1. Read the Universal Workstation instruction manual care-
fully before assembling the workstation and mounting the
miter saw.
2. This Universal Workstation is designed to be used with
HITACHI (C8FB2, C10FCB, C10FM, C10FCD,C10FSH/FSB),
DEWALT (DW703, DW705S, DW706,DW708), and DELTA
(36-075, MS275) Miter Saws . Use with additional Miter
Saw models has not yet been verified.
3. The Miter Saw should be firmly mounted to the Universal
Workstation per the instruction manual.
4. After mounting the Miter Saw to the Universal
Workstation, align, position and balance the Miter Saw
per the instruction manual.
5. Before use, verify that all Universal Workstation parts are
free from damage and/or deformity.
6. Before use, verify that all parts or components of the
Universal Workstation are properly installed.
7. Before use, swing open each of the legs until the brass
pin clicks, locking the legs in position.
8. When mounting the Miter Saw to the Universal
Workstation, make sure that the tool mount handles are
in the “UNLOCK” position, so the tool mount will engage
with the main beam. Be sure to hold the saw until it
is secured to prevent it from falling off the main beam.
Handles should then be tightened.
9. Before operating the Miter Saw, confirm that the
tool mount handles on both sides of this Universal
Workstation are firmly tightened insuring that the Miter
Saw is securely mounted to the Workstation.
10. When removing the Miter Saw from the Universal
Workstation, loosen the tool mount handles until they
rotate to the “UNLOCK”” position. Hold the Miter Saw
firmly to prevent the saw from falling off the main beam.
Carefully remove the Miter Saw.
11. Disconnect the power plug from the power outlet when
mounting or dismounting the Miter Saw to the Universal
Workstation.
12. Do not modify the Universal Workstation in any manner
or use the Universal Workstation for any purpose other
than is stated in these instructions.
13. Do not sit or stand on the Universal Workstation. Do
not place, hang, or install anything on the Universal
Workstation other than a Miter Saw.
14. Always use this universal workstation on a level surface.
Do not use it on uneven or unstable surfaces.
15. Before operating the mounted Miter Saw, read the Miter
Saw instruction manual carefully.
16. Because cut material may cause the workstation to
become unbalanced, always be sure the material is sup-
ported properly. Also, if the piece being cut is placed far
beyond the work support, workstation legs on the oppo-
site side may suddenly be lifted up due to weight imbal-
ance. To prevent this from occurring, hold the opposite
side firmly before cutting.
IMPORTANT SAFETY INSTRUCTIONS FOR USING THIS UNIVERSAL WORKSTATION
(100 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals