Delta Delta JT360 Instruction Manual

INSTRUCTION MANUAL6" Deluxe Jointer(Model JT360)PART NO. A05753 - 09-17-024Copyright © 2004 Delta MachineryESPAÑOL: PÁGINA 29To learn more about

10ASSEMBLYASSEMBLY TOOLS REQUIREDASSEMBLY TIME ESTIMATE - 2-3 hoursFOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THEMACHIN

11Fig. 7Fig. 8MOTOR AND SWITCH TO STAND1. Assemble motor (B) Fig. 7, to the bottom of the dustchute. Align the four holes (F) Fig. 7, in the dust chut

Fig. 11D12Fig. 10D3. Using the supplied wrench (or a 14 mm socketwrench), fasten the jointer to the top of stand using thethree M10.2 lockwashers and

13Fig. 13Fig. 12INFEED TABLE ADJUSTMENTHANDLE1. Turn locknut (C) Fig. 12, clockwise on infeed tableadjustment handle (B) as far as it will go.2. Threa

14MOTOR PULLEYAssemble motor pulley (A) Fig. 16, to motor shaft withthe hub of the pulley in the outer position as shown.Make sure key (B) is inserted

15Fig. 22Fig. 21MOTOR PULLEY AND BELT GUARDAssemble the motor pulley and belt guard (A) Fig. 19, tothe jointer base using the four M6x1x10mm cheese he

16Fig. 23Fig. 241. Remove set screw (A) Fig. 23, from post (B) ofcutterhead guard (C).2. Assemble cutterhead guard (C) Fig. 23, to the jointerby inser

17Fig. 36Fig. 35INFEED TABLE ADJUSTMENTS1. To raise or lower the infeed table, loosen tablelockhandle (A) Fig. 35, move the table raising andlowering

18Fig. 39Fig. 40STEEL STRAIGHT EDGEOUT-FEED TABLEIN-FEEDTABLECUTTER3. Place a straight edge on the outfeed table, extendingover the cutterhead as show

19Fig. 46Fig. 47Fig. 48Fig. 49ADJUSTING TABLE GIBS“Gibs” are provided to take up all play between the matingdovetail ways of the base and the infeed a

TABLE OF CONTENTSRead and understand all warnings and operating instructions before using any tool or equipment. Whenusing tools or equipment, basic

20Fig. 50Fig. 51Fig. 52Fig. 53Fig. 54ADJUSTING FENCE POSITIVE STOPSThe fence on this jointer is equipped with positive stopsthat allow you to rapidly

21BFig. 55 Fig. 56Fig. 58Fig. 573. Using 8x10 mm open end wrench (A) Fig. 57, slightlyloosen the four locking screws (B) in each knife slot byturning

22Fig. 59Fig. 60Fig. 619. The knives are adjusted correctly when the cuttingedge of the knife extends out .060" (1.5 mm) from thecutterhead diame

23Fig. 66Fig. 65DO NOT PERFORM JOINTINGOPERATIONS ON MATERIAL SHORTERTHAN 10 INCHES (254 mm), NARROWER THAN 3/4INCH (19 mm), OR LESS THAN 1/2 INCH (12

24PLANING OR SURFACINGPlaning or surfacing is identical to the jointing operationexcept for the position of the workpiece. For planing, themajor flat

25PLANING WARPED PIECESIf the wood to be planed is dished or warped, take lightcuts until the surface is flat. Avoid forcing such materialdown against

26Fig. 71REMOVING DUST CHUTE COVERThe dust chute cover (A) Fig. 71, can be removed, forcleaning purposes, by removing the two wing screws (B). MAKE CE

27PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof P

28NOTES

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marquessuivantes sont de

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

4GENERAL SAFETY RULESREAD AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFOREUSING THIS EQUIPMENT. Failure to follow all instructions listed

5FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.ADDITIONAL SAFETY RULES FOR JOINTERS SAVE THESE INSTRUCTIONS. Refer to them often

6A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

7done by qualified electrical personnel. Should you desire tohave your jointer converted for 240 volts, take your jointer toyour local Authorized Delt

Fig. 4Fig. 4A134567891011121314151617181922232422021252627282930313233343536378Fig. 4BUNPACKING AND CLEANING WARNING: JOINTER WEIGHT IS APPROXIMATELY

9JOINTER PARTSFig. 41. Motor and Switch2. Jointer3. Motor Pulley4. V-Belt5. Two Top End Braces for Stand (11-3/4")6. Two Top Side Braces for Stan