4
ADDITIONAL SPECIFIC SAFETY RULES
1. DO NOT OPERATE THIS MACHINE until it is completely
assembled and installed according to the instructions.
A machine incorrectly assembled can cause serious injury.
2. OBTAIN ADVICE from your supervisor, instructor, or
another qualied person if you are not thoroughly familiar
with the operation of this machine. Knowledge is safety.
3. FOLLOW ALL WIRING CODES and recommended electrical
connections to prevent shock or electrocution.
4. SECURE THE MACHINE TO A SUPPORTING SURFACE.
Vibration can cause the machine to slide, walk, or tip over.
5. NEVER START THE MACHINE BEFORE CLEARING
THE TABLE OF ALL OBJECTS (tools,scrappieces,etc.).
Debris can be thrown at high speed.
6. NEVER START THE MACHINE with the drill bit, cutting
tool, or sanding drum against the workpiece. Loss of
control of the workpiece can cause serious injury.
7. PROPERLY LOCK THE DRILL BIT, CUTTING TOOL, OR
SANDING DRUM IN THE CHUCK before operating this
machine.
8. REMOVE THE CHUCK KEY BEFORE STARTING THE
MACHINE. The chuck key can be thrown out at a high
speed.
9. TIGHTEN ALL LOCK HANDLES before starting the machine.
Loss of control of the workpiece can cause serious injury.
10. USE ONLY DRILL BITS, CUTTING TOOLS, SANDING
DRUMS, OR OTHER ACCESSORIES with shank size
recommended in your instruction manual. The wrong size
accessory can cause damage to the machine and/or
serious injury.
11. USE ONLY DRILL BITS, CUTTING TOOLS, OR
SANDING DRUMS that are not damaged. Damaged items
can cause malfunctions that lead to injuries.
12. USE RECOMMENDED SPEEDS for all operations. Other
speeds may cause the machine to malfunction causing
damage to the machine and/or serious injury.
13. AVOID AWKWARD OPERATIONS AND HAND
POSITIONS. A sudden slip could cause a hand to move
into the bit.
14. KEEP ARMS, HANDS, AND FINGERS away from the bit.
Serious injury to the hand can occur.
15. HOLD THE WORKPIECE FIRMLY AGAINST THE TABLE.
Do not attempt to drill a workpiece that does not have a
atsurfaceagainstthetable,orthat isnotsecuredbya
vise. Prevent the workpiece from rotating by clamping it to
the table or by securing it against the drill press column.
Loss of control of the workpiece can cause serious injury.
16. TURN THE MACHINE “OFF” AND WAIT FOR THE DRILL
BIT, CUTTING TOOL, OR SANDING DRUM TO STOP
TURNING prior to cleaning the work area, removing
debris,removing or securingwork-piece,orchanging
the angle of the table. A moving drill bit, cutting tool, or
sanding drum can cause serious injury.
1 7. PROPERLY SUPPORT LONG OR WIDE work-pieces.
Loss of control of the workpiece can cause severe injury.
18. DO NOT PLACE more than 250 pounds of weight on the
table.
19. NEVER PERFORM LAYOUT, ASSEMBLY OR SET-
UP WORK on the table/work area when the machine is
running. Serious injury can result.
20. TURN THE MACHINE “OFF”, disconnect the machine
from the power source, and clean the table/work area
before leaving the machine. LOCK THE SWITCH IN THE
“OFF” POSITION to prevent unauthorized use. Someone
else might accidentally start the machine and cause
serious injury to themselves.
2 1. ADDITIONAL INFORMATION regarding the safe
and proper operation of power tools (i.e. a safety
video)isavailablefromthe PowerToolInstitute,1300
SumnerAvenue, Cleveland, OH 44115-2851 (www.
powertoolinstitute.com). Information is also available
from the National Safety Council, 1121 Spring
LakeDrive,Itasca,IL60143-3201. Please refertothe
American National StandardsInstituteANSI01.1 Safety
Requirements for WoodworkingMachines and the
U.S.DepartmentofLaborOSHA1910.213Regulations.
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.
ADDITIONAL SAFETY RULES FOR THE LASERS
SAFETY INSTRUCTIONS FOR LASERS
Read and understand all instructions. Failure to follow all instructions listed below may result in electric
shock, re and/or serious personal injury.
For your own safety, read the tool instruction manual before using any accessory. Failure to heed these warn-
ings may result in personal injury and serious damage to the tool and the accessory. When servicing this tool, use only iden-
tical replace ment parts.
LASER RADIATION EXPOSURE. Do not disassemble or modify the laser. There are no user serviceable parts
inside. Serious eye injury could result.
HAZARDOUS RADIATION.Useormodicationofthetoolforanythingotherthanitsdesignedpurposemayresultin
hazardousradiationexposure.
• Donotoperatethelaserinexplosiveatmospheres,suchasinthepresenceofammableliquids,gases,ordust.Powertoolscre-
ate sparks which may ignite the dust or fumes.
• Storeidlelaseroutofreachofchildrenandotheruntrainedpersons.Lasersaredangerousinthehandsofuntrainedusers.
• Toolservicemustbeperformedonlybyqualiedrepairpersonnel.Serviceormaintenanceperformedbyunqualiedpersonnelmay
resultininjury.TolocateyournearestDELTA®servicecentercall1-800-223-7278orgotowww.DeltaMachinery.com on the Internet.
• Donotuseopticaltoolssuchasatelescopeortransittoviewthelaserbeam.Seriouseyeinjurycouldresult.
• Donotstareintobeamaperture,orintoareectionfromamirror-likesurface
• Donotplacethelaserinapositionwhichmaycauseanyonetointentionallyorunintentionallystareintothelaserbeam.Serious
eye injury could result.
• Turnthelaseroffwhenitisnotinuse.Leavingthelaseronincreasestheriskofstaringintothelaserbeam.
• Donotdisassemblethelaserorlaserpowersupply.Therearenouserserviceablepartsinside.
• Donotmodifythelaserinanyway.ModifyingthetoolmayresultinHazardousLaserRadiationExposure.
• Donotoperatethelaseraroundchildrenorallowchildrentooperatethelaser.Seriouseyeinjurymayresult.
• Donotremoveordefacewarninglabels.Removinglabelsincreasestheriskofexposuretoradiation.
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct others.
Comments to this Manuals