Delta MS450 Instruction Manual download pdf (Page 5)

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

1. DO NOT OPERATE THIS MACHINE UNTIL it is

assembled and installed according to the

instructions.

2. OBTAIN ADVICE from your supervisor, instructor,

or another qualified person if you are not familiar

with the operation of this machine.

3. FOLLOW ALL WIRING CODES and recommended

electrical connections.

4 MOUNT THE TOOL SECURELY to a stable

supporting surface prior to operation

5. DO NOT OPERATE SAW WITHOUT GUARDS IN

PLACE. Check to see that they are in place,

secured, and working correctly.

6. USE ONLY CROSSCUT SAW BLADES. Use only

zero-degree or negative hook angles when using

carbide-tipped blades. Do not use blades with deep

gullets. These can deflect and contact the guard.

7. USE ONLY BLADES OF THE CORRECT SIZE AND

TYPE specified for this tool.

8. USE A SHARP BLADE. Check blade to see if it runs

freely and is free from vibration.

9. INSPECT BLADE FOR CRACKS or other damage

prior to operation. Replace cracked or damaged

blade immediately.

10. CLEAN THE BLADE AND BLADE FLANGES prior

to operation. Check for any damage and tighten the

arbor nut securely.

11. USE ONLY BLADE FLANGES specified for this tool.

12. CLEAR THE AREA OF FLAMMABLE LIQUIDS

and/or gas prior to operation.

13. CLEAN THE MOTOR AIR SLOTS of chips and

sawdust.

14. TIGHTEN THE TABLE CLAMP HANDLE and any

other clamps prior to operation.

15. NEVER START THE TOOL with the workpiece

against the blade.

16. KEEP HANDS out of path of saw blade. Clamp all

workpieces that would require your hand to be in the

“Table Hazard Zone” (within the red lines).

17. ALLOW THE MOTOR to come to full speed prior to

starting cut.

18. NEVER REACH AROUND or behind the saw blade.

19. NEVER CUT FERROUS METALS or masonry.

ADDITIONAL SAFETY RULES FOR MITER SAWS

20. NEVER RECUT SMALL PIECES.

21. NEVER LOCK THE SWITCH in the “ON” position.

22. NEVER APPLY LUBRICANT to a running blade.

23. DO NOT PERFORM FREE-HAND OPERATIONS.

Hold the work firmly against the fence and table.

Use clamps to hold the work when possible.

24. PROPERLY SUPPORT LONG or wide workpieces.

25. AFTER COMPLETING CUT, release power switch

and wait for coasting blade to come to a complete

stop before returning saw to raised position. Make

sure saw cuttinghead returns freely to the full raised

position to ensure the lower blade guard fully

encloses the blade.

26. TURN OFF TOOL AND ALLOW THE BLADE TO

COME TO A COMPLETE STOP prior to cleaning

the blade area or removing debris in the path of the

blade. A coasting blade can be dangerous.

27. TURN OFF TOOL AND ALLOW BLADE TO COME

TO A COMPLETE STOP before removing or

securing workpiece, changing workpiece angle, or

changing the angle of the blade.

28. NEVER PERFORM LAYOUT, ASSEMBLY, or set-

up work on the table/work area when the machine is

running.

29. TURN THE MACHINE “OFF” AND DISCONNECT

THE MACHINE from the power source before

installing or removing accessories, before adjusting

or changing set-ups, or when making repairs.

30. TURN THE MACHINE “OFF”, disconnect the

machine from the power source, and clean the

table/work area before leaving the machine. LOCK

THE SWITCH IN THE “OFF” POSITION to prevent

unauthorized use.

31. ADDITIONAL INFORMATION regarding the safe

and proper operation of this tool, including a miter

saw safety video, is available from the Power Tool

Institute, 1300 Summer Avenue, Cleveland, OH

44115-2851. Information is also available from the

National Safety Council, 1121 Spring Lake Drive,

Itasca, IL 60143-3201. Please refer to the American

National Standards Institute ANSI 01.1 Safety

Requirements for Woodworking Machines and the

U.S. Department of Labor OSHA 1910.213

Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others

1 2 3 4 5 6 7 8 9 10 ... 22 23

Comments to this Manuals

No comments

Delta MS450 Instruction Manual Page 5

Comments to this Manuals