Delta TP305 Instruction Manual Page 5
- Page / 48
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5
1. DO NOT OPERATE THIS MACHINE until it is
completely assembled and installed according to the
instructions. A machine incorrectly assembled can
cause serious injury.
2. OBTAIN ADVICE from your supervisor, instructor,
or another qualified person if you are not thoroughly
familiar with the operation of this machine.
Knowledge is safety.
3. FOLLOW ALL WIRING CODES and recommend-
ed electrical connections to prevent shock or
electrocution.
4. KEEP KNIVES SHARP and free from rust and pitch.
Dull or rusted knives work harder and can cause
kickback.
5. NEVER TURN THE MACHINE "ON" before clearing
the table of all objects (tools, scraps of wood, etc.).
Flying debris can cause serious injury.
6. NEVER TURN THE MACHINE "ON" with the work-
piece contacting the cutterhead. Kickback can
occur.
7. SECURE THE MACHINE TO A SUPPORTING SUR-
FACE to prevent the machine from sliding, walking
or tipping over.
8. PROPERLY SECURE THE KNIVES IN THE CUTTER-
HEAD before turning the power "ON". Loose blades
may be thrown out at high speeds causing serious
injury.
9. LOCK THE SPEED SETTING SECURELY before
feeding the workpiece through the machine.
Changing speeds while planing can cause kick-
back.
10. AVOID AWKWARD OPERATIONS AND HAND POSI-
TIONS. A sudden slip could cause a hand to move
into the knives.
11. KEEP ARMS, HANDS, AND FINGERS away from
the cutterhead, the chip exhaust opening, and the
feed rollers to prevent severe cuts.
12. NEVER REACH INTO THE CUTTERHEAD AREA
while the machine is running. Your hands can be
drawn into the knives.
13. DO NOT STAND IN LINE OF THE WORKPIECE.
Kickback can cause injury.
14. ALLOW THE CUTTERHEAD TO REACH FULL SPEED
before feeding a workpiece. Changing speeds while
planing can cause kickback.
15. WHEN PLANING BOWED STOCK, place the concave
(cup down) side of the stock on the table and cut
with the grain to prevent kickback.
16. DO NOT FEED A WORKPIECE that is warped, contains
knots, or is embedded with foreign objects (nails,
staples, etc.). Kickback can occur.
17. DO NOT FEED A SHORT, THIN, OR NARROW
WORKPIECE INTO THE MACHINE. Your hands can
be drawn into the knives and/or the workpiece can
be thrown at high speeds. See the "OPERATION"
section of this instruction manual for details.
18. DO NOT FEED A WORKPIECE into the outfeed end of
the machine. The workpiece will be thrown out of the
opposite side at high speeds.
19. REMOVE SHAVINGS ONLY with the power "OFF" to
prevent serious injury.
20. PROPERLY SUPPORT LONG OR WIDE WORK-
PIECES. Loss of control of the workpiece can cause
serious injury.
21. NEVER PERFORM LAYOUT, ASSEMBLY or set-up
work on the table/work area when the machine is
running. Serious injury will result.
22. TURN THE MACHINE "OFF", DISCONNECT IT FROM
THE POWER SOURCE, and clean the table/work area
before leaving the machine. LOCK THE SWITCH IN
THE "OFF" POSITION to prevent un-authorized use.
Someone else might accidentally start the machine
and cause injury to themselves or others.
23. ADDITIONAL INFORMATION regarding the safe
and proper operation of power tools (i.e. a safety
video) is available from the Power Tool Institute, 1300
Sumner Avenue, Cleveland, OH 44115-2851 (www.
powertoolinstitute.com). Information is also available
from the National Safety Council, 1121 Spring Lake
Drive, Itasca, IL 60143-3201. Please refer to the
American National Standards Institute ANSI 01.1
Safety Requirements for Woodworking Machines
and the U.S. Department of Labor Regulations.
Failure to follow these rules may result in serious personal injury.
ADDITIONAL SPECIFIC SAFETY RULES
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct others.
- 10" Contractors Saw 1
- IMPORTANT SAFETY INSTRUCTIONS 2
- TABLE OF CONTENTS 2
- CALIFORNIA PROPOSITION 65 3
- GENERAL SAFETY RULES 4
- SAVE THESE INSTRUCTIONS 5
- POWER CONNECTIONS 6
- MOTOR SPECIFICATIONS 6
- GROUNDING INSTRUCTIONS 6
- FUNCTIONAL DESCRIPTION 7
- CARTON CONTENTS 7
- ASSEMBLY 8
- OPERATION 9
- LEVELING EXTENSION TABLES 11
- KNIFE TRANSFER TOOL STORAGE 11
- WRENCH STORAGE 11
- CARRYING HANDLE/STOCK 12
- TRANSFER BAR 12
- REPLACING KNIVES 12
- TROUBLESHOOTING 14
- MAINTENANCE 14
- BRUSH INSPECTION AND 15
- REPLACEMENT 15
- LUBRICATION 15
- ACCESSORIES 16
- WARRANTY 16
- FRANÇAISE 17
- CONSERVEZ CES INSTRUCTIONS! 18
- RÈGLES DE SÉCURITÉ GÉNÉRALES 19
- CONSERVER CES DIRECTIVES 20
- RACCORDEMENTS ÉLECTRIQUES 21
- SPÉCIFICATIONS DU MOTEUR 21
- DESCRIPTION FONCTIONNELLE 22
- CONTENUS DE BOITE 22
- ASSEMBLAGE 23
- FONCTIONNEMENT 24
- POSITION D’ARRÊT 25
- RANGEMENT DE L’OUTIL DE 26
- TRANSFERT DU FER 26
- RANGEMENT DE LA CLÉ 26
- TRANSFERT DE MATÉRIAU 27
- REMPLACEMENT DES FERS 27
- Fig. 22 28
- ENTRETIEN 29
- DEPANNAGE 29
- INSPECTION ET REMPLACEMENT 30
- DE LA BROSSE 30
- LUBRIFICATION 30
- ACCESSOIRIES 31
- GARANTIE 32
- PROPOSICIÓN DE CALIFORNIA 65 34
- NORMAS GENERALES DE SEGURIDAD 35
- GUARDE ESTAS INSTRUCCIONES 36
- ESPECIFICACIONES DEL MOTOR 37
- DESCRIPCIÓN FUNCIONAL 38
- CONTENIDO DE CARTON 38
- ENSAMBLAJE 39
- OPERACIÓN 40
- FIJANDO EL INTERRUPTOR EN LA 41
- POSICION DE APAGADO 41
- ELEVANDO Y BAJANDO EL 41
- CONJUNTO DEL CABEZAL 41
- AGARRADERA DE TRANSPORTE/ 43
- BARRA DE TRANSFERENCIA DE 43
- MATERIAL 43
- REEMPLAZANDO LAS CUCHILLAS 43
- MANTENIMIENTO 45
- LOCALIZACION DE FALLAS 45
- INSPECCION Y REEMPLAZO DE 46
- CEPILLOS 46
- LUBRICACION 46
- SERVICIO 47
- ACCESORIOS 47
- GARANTIA 47
- Delta Machinery 48
- 4825 Highway 45 North 48
- Jackson, TN 38305 48
Related products and manuals for Power tools Delta TP305
Power tools Delta 36-205 User Manual
(4 pages)
(4 pages)
Power tools Delta 23-700 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 23-725 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta ts200ls Instruction Manual
(27 pages)
(27 pages)
Power tools Delta 23-710 Instruction Manual
(64 pages)
(64 pages)
Power tools Delta DP350 Instruction Manual
(17 pages)
(17 pages)
Power tools Delta BS150LS Instruction Manual
(25 pages)
(25 pages)
Power tools Delta 50-760 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 23-710 Instruction Manual
(24 pages)
(24 pages)
Power tools Delta 36-979 Instruction Manual
(17 pages)
(17 pages)
Power tools Delta 33-892 Instruction Manual
(28 pages)
(28 pages)
Power tools Delta 28-206 Instruction Manual
(24 pages)
(24 pages)
Power tools Delta 50-860 Specifications
(12 pages)
(12 pages)
Power tools Delta 11-985 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 23-700 Instruction Manual
(10 pages)
(10 pages)
Power tools Delta 23-725 Instruction Manual
(20 pages)
(20 pages)
Power tools Delta DJ-15 Instruction Manual
(24 pages)
(24 pages)
Power tools Delta 36-714B Instruction Manual
(76 pages)
(76 pages)
GE DBSR463GGWW manuály
Uživatelské manuály a uživatelské příručky pro Sušičky GE DBSR463GGWW.
Poskytujeme 1 manuály pdf GE DBSR463GGWW ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comments to this Manuals