Delta 31-260X Instruction Manual Page 12
- Page / 60
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
12
IMPORTANT: The sanding drum speed is 3300 SFPM with the belt on the inner pulleys (A) Fig. 27. The drum speed is 2210
SFPM with the belt positioned on the outer pulleys (A) Fig. 26.
NOTE: Position the poly-v drive belt on the pulleys correctly to provide max i mum performance with minimal belt wear.
4. After you have replaced or repositioned the belt on the pulleys, apply downward pressure on the motor and tighten the
two hex-head bolts that were loosened in STEP 3.
5. Use light finger pressure on the belt midway between the pulleys to check for proper tension. A deflection of
approximately 3/16" (5 mm) is correct.
6. Replace the hole plugs (B) Fig. 25.
A spring clip on each side of the drum holds the sanding belt in place.
Fig. 26
Fig. 27
Fig. 28
Fig. 30
Fig. 29
HOW TO REMOVE AND REPLACE THE DRUM SANDING BELT
A
A
A
C
B
C
A
B
A
D
B
1. Open the drum cover.
2. Press the spring clip (B) Fig. 28 together and remove one end of sanding belt (A).
NOTE: The clip must be fully depressed against the drum support.
3. Rotate the drum (C) Fig. 29 by hand until you reach the other spring clip. Squeeze that spring clip open to remove the
sanding belt.
4. To replace the sanding belt, press the spring clip (B) Fig. 29 together and insert one end of the sanding belt (A) through
the slot in the drum and into the spring clip. Align the tapered end of the sanding belt with the edge of the drum.
5. Tightly wrap the sanding belt (A) Fig. 30 around the drum cylinder (D), keeping each wrap close to the previous edge.
IMPORTANT: Do Not overlap the edges of the sanding belt (A)
.
6. Insert the other end of the sanding belt into the left spring clip as tightly as possible.
The sanding belt will stretch during use. Periodically, press the spring clip and tighten the belt in the clip.
The drum sander has two drum speeds - 2210 SFM or 3300 SFM
(205.3 or 306.6 m
2
/min).
To change the sanding drum speeds or to replace the drive belt:
To reduce the risk of injury, turn unit off and disconnect it
from power source before installing and removing accessories, before
adjusting or when making repairs. An accidental start-up can cause injury.
1. Raise the top drum cover (A) Fig. 25.
2. Remove the two hole plugs (B) Fig. 25.
3. Place a 9/16" socket with an extension (not supplied) in one of the two
holes where the hole plugs were re moved.
NOTE: If you do not have a socket extension, remove the bolts (G) Fig. 25
from the panel to get to the bolts. Loosen one hex bolt, then the other
to relieve tension on
the motor. Slightly lift the motor (located under
the machine) to relieve tension on the belt. Replace or change the belt
po si tions on the pulleys.
G
A
G
B
HOW TO CHANGE THE DRUM SPEEDS
AND REPLACE THE DRIVE BELT
Fig. 25
To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing
accessories, before adjusting or when making repairs. An accidental start-up can cause injury.
- Instruction manual 1
- Manuel d’utilisation 1
- Manual de instrucciones 1
- TABLE OF CONTENTS 2
- IMPORTANT SAFETY INSTRUCTIONS 2
- GENERAL SAFETY RULES 3
- SAVE THESE INSTRUCTIONS 4
- MINIMUM GAUGE EXTENSION CORD 5
- FUNCTIONAL DESCRIPTION 6
- CARTON CONTENTS 6
- ASSEMBLY 7
- HOW TO ATTACH THE HANDWHEEL 8
- HOW TO LOCK THE DRUM SWITCH 9
- TO CHECK AND ADJUST TRACKING 10
- TO CHECK AND ADJUST TENSION 10
- HOW TO RAISE THE TABLE 10
- HOW TO SET THE HEIGHT SCALE 11
- PARALLEL TO THE DRUM 11
- AND REPLACE THE DRIVE BELT 12
- Fig. 35A 13
- FREQUENTLY ASKED QUESTIONS 14
- HOW DO I GET STARTED? 16
- STEP 1 - TIMING BELT TENSION 17
- MAINTENANCE 18
- TROUBLESHOOTING 18
- KEEP MACHINE CLEAN 19
- FAILURE TO START 19
- REPLACEMENT PARTS 19
- ACCESSORIES 20
- WARRANTY 20
- RÈGLES DE SÉCURITÉ GÉNÉRALES 22
- CONSERVER CES DIRECTIVES 23
- CORDON DE RALLONGE 24
- DESCRIPTION FONCTIONNELLE 25
- CONTENUS DE BOITE 25
- ASSEMBLAGE 26
- CAUTION 27
- ÉLÉVATION DE LA TABLE 29
- LA TABLE AU TAMBOUR 30
- Un démarrage accidentel 31
- PAR OÙ DOIS-JE COMMENCER? 35
- ENTRETIEN 37
- DEPANNAGE 37
- GARDER LA MACHINE PROPRE 38
- DÉMARRAGE IMPOSSIBLE 38
- PIÈCES DE RECHANGE 38
- ACCESSOIRIES 39
- GARANTIE 39
- NORMAS GENERALES DE SEGURIDAD 41
- GUARDE ESTAS INSTRUCCIONES 42
- CORDONES DE EXTENSIÓN 43
- DESCRIPCIÓN FUNCIONAL 44
- CONTENIDO DE CARTON 44
- ENSAMBLAJE 45
- ATENCION 46
- CÓMO INSTALAR EL VOLANTE 46
- CÓMO ELEVAR LA MESA 48
- PARALELA AL TAMBOR 49
- LA BANDA IMPULSORA 50
- HIZO CON FRECUENCIA PREGUNTAS 52
- ¿CÓMO EMPIEZO? 54
- LOCALIZACION DE FALLAS 56
- MANTENIMIENTO 57
- SERVICIO 57
- ACCESORIOS 58
- PÓLIZA DE GARANTÍA 58
- GARANTIA 59
- www.deltaportercable.com 60
Related products and manuals for Power sanders Delta 31-260X
(50 pages)
(60 pages)
Power sanders Delta 31-750 User Manual
(100 pages)
(100 pages)
Power sanders Delta SA446 Instruction Manual
(23 pages)
(23 pages)
Power sanders Delta 31-495 User Manual
(82 pages)
(82 pages)
Power sanders Delta 31-250 User Manual
(1 pages)
(1 pages)
Power sanders Delta 31 Instruction Manual
(21 pages)
(21 pages)
Power sanders Delta 31-483 User Manual
(10 pages)
(10 pages)
© 2020, manymanuals.com. All rights reserved. | 0.980 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals