61300 Rev.E
Metal Pop-up
A.
Remove stopper (1) and flange (2).
B.
Screwnut(1)allthewaydown.Push
washer (2) and gasket (3) down.
C.
Remove tailpiece (1) from body (2), add
plumber tape (3), replace tailpiece.
D.
Applysiliconetoundersideofflange(1).
Insert body (2) into sink. Screw flange (1)
into body (2).
E.
Pivot(1)mustfacefaucet.Pullassembly
(2) down firmly and hold in place.
DONOTTWIST.
F.
Tightennut/washer/gasket(1),cleanoff
excesssilicone(2).DONOTTWIST.
A.
B.
C.
D.
E.
F.
G.
G.
Remove pivot nut (1). Install horizontal rod (2) and
stopper (3) as removable (4) or non-removable (5).
Handtightenpivotnut(1).
H.
Attachhorizontalrod(1)tostrap(2)using
clip (3). Insert lift rod (4) into strap and tighten
screw(5).Connectassemblytodrain(6).
Desagüe automático de metal
A.
Quite el tapón (1) y el reborde (2).
B.
Atornillelatuerca(1)completamentehasta
abajo.Empujelaarandela/roldana(2)yel
(3) hacia abajo.
C.
Quite el tubo de cola (1) del cuerpo (2),
aplique cinta plomero (3), coloque otra vez
el tubo de cola.
D.
Apliquesilicónalaparteinteriordelreborde
(1). Inserte el cuerpo (2) en el lavamanos.
Atornilleelreborde(1)enelcuerpo(2).
E.
Elpivote(1)debedeestardefrenteala
llave.Haleelensamble(2)haciaabajo
firmementeysujételoensitio.NOLOGIRE.
F.
Aprietelatuerca/arandela/empaque(1),
limpieelexcesodesilicón(2).NOLOGIRE.
G.
Quite la tuerca del pivote (1). Instale la barra
horizontal (2) y el tapón (3) como desmontable (4)
ofijo(5).Aprieteamanolatuercadel
pivote (1).
H.
Una la barra horizontal (1) a la barra chata
(2) utilizando el gancho (3). Introduzca la barra de
alzar (4) dentro de la barra chata de articulación
yaprieteeltornillo(5).Conecteelensambleal
desagüe (6).
Renvoi mécanique en métal
A.
Enlevezlabonde(1)etlacollerette(2).
B.
Serrez l’écrou (1) pour le faire descendre
complètement.Poussezlarondelle(2)et
le joint (3) vers le bas.
C.
Enlevezleraccorddroitdevidange(1)du
corps (2), appliquez du ruban de plomberie
(3), puis remettez raccord droit en place.
D.
Appliquezducomposéàlasiliconesousla
collerette (1). Introduisez le corps (2) dans
le lavabo, puis vissez la collerette (1) dans le
corps (2).
E.
Lepivot(1)doitfairefaceaurobinet.Tirez
l’ensemble (2) vers le bas fermement et
maintenez-leenplace.PRENEZGARDE
DELETORDRE.
F.
Serrez l’écrou contre la rondelle et le joint (1),
puis enlevez le surplus de composé à la silicone
(2).PRENEZGARDEDETORDRELEPIVOT.
G.
Enlevezl’écroudupivot(1).Installezlatige
horizontale (2) et la bonde (3) de manière que
la bonde soit amovible (4) ou non amovible (5).
Serrez l’écrou (1) du pivot à la main.
H.
Fixezlatigehorizontale(1)aufeuillard(2)à
l’aide de l’agrafe (3). Installez la tige de mano-
euvre(4)etserrezlavis(5).Fixezl’ensembleau
renvoi (6).
1
2
1
2
3
1
2
3
1
2
1
2
1
2
1
4
3
5
2
3
2
H.
1
5
3
4
2
6
Comments to this Manuals