Delta JT160 Instruction Manual Page 16
- Page / 21
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
The following directions will give the beginner a start on jointer operations. Use scrap pieces of lumber to check the
settings and to get the feel of the operations before attempting regular work.
NOTE: The knives on the jointer will not wear evenly by feeding the wood through the same spot on the table
every time. Feed the wood through the jointer at different spots on the table to help eliminate uneven wear of
the knives.
ALWAYS USE CUTTERHEAD GUARD AND KEEP HANDS AWAY FROM CUTTERHEAD. USE PUSH
BLOCKS WHENEVER POSSIBLE.
Fig. 37C
PLACEMENT OF HANDS
DURING FEEDING
At the start of the cut, the left hand holds the work firmly
against the infeed table and fence, while the right hand
pushes the work toward the knives. After the cut is un-
derway, the new surface rests firmly on the outfeed table
as shown in Fig. 37C. The left hand should then be
moved to the work on the outfeed table, at the same
time maintaining flat contact with the fence. The right
hand presses the work forward, and before the right
hand reaches the cutterhead it should be moved to the
work on the outfeed table.
NEVER PASS HANDS DIRECTLY
OVER THE CUTTERHEAD.
JOINTING AN EDGE
This is the most common operation for the jointer. Set
the guide fence square with the table. Depth of cut
should be the minimum required to obtain a straight
edge. Hold the best face of the piece firmly against the
fence throughout the feed as shown in Fig. 38.
DO NOT PERFORM JOINTING OPERA-
TIONS ON MATERIAL SHORTER THAN
10 INCHES (254 mm), NARROWER
THAN 3/4 INCH (19 mm), OR LESS
THAN 1/2 INCH (12.7 mm) THICK
(REFER TO FIG. 39).
Fig. 39
OUT-FEED
TABLE
IN-FEED TABLE
CUTTER
MATERIAL
3/4" (19 mm) MINIMUM
10" (254 mm) MINIMUM
MINIMUM JOINTING DIMENSIONS
1/2" (12.7 mm)
MINIMUM
MACHINE USE
Fig. 37A
Fig. 37B
1. JOINTING OPERATIONS – Jointing cuts or edge
jointing are made to square an edge of a workpiece.
The workpiece is positioned on the jointer with the
narrow edge of the workpiece on the infeed table
and the major flat surface of the workpiece against
the fence, as shown in Fig. 37A. The workpiece is
moved from the infeed table, across the cutterhead
to the outfeed table.
2. PLANING OPERATIONS – Planing or surfacing are
identical to the jointing operation except for the
position of the workpiece. For planing, the major flat
surface of the workpiece is placed on the infeed
table of the jointer with the narrow edge of the
workpiece against the fence, as shown in Fig. 37B.
The workpiece is moved from the infeed table,
across the cutterhead to the outfeed table. Use push
blocks when performing planing operations
whenever possible.
16
DEFINITION OF JOINTING, PLANING
- 6" Variable Speed 1
- Bench Jointer 1
- TABLE OF CONTENTS 2
- IMPORTANT SAFETY INSTRUCTIONS 2
- CALIFORNIA PROPOSITION 65 3
- GENERAL SAFETY RULES 4
- SAVE THESE INSTRUCTIONS 5
- Refer to them often 5
- POWER CONNECTIONS 6
- MOTOR SPECIFICATIONS 6
- GROUNDING INSTRUCTIONS 6
- FUNCTIONAL DESCRIPTION 7
- CARTON CONTENTS 8
- ASSEMBLY 9
- CUTTERHEAD GUARD 10
- CUTTERHEAD LOCK 11
- OPERATION 12
- DEPTH OF CUT ADJUSTMENT 13
- FENCE ADJUSTMENTS 13
- ADJUSTING KNIVES 14
- PUSH BLOCKS 15
- CHIP AND DUST CHUTE 15
- MACHINE USE 16
- TROUBLESHOOTING 17
- MAINTENANCE 18
- ACCESSORIES 19
- WARRANTY 20
- • DELTA SERVICE CENTERS 21
- • DELTA) 21
Related products and manuals for Power tools Delta JT160
Power tools Delta GR150 Instruction Manual
(15 pages)
(15 pages)
Power tools Delta 50-770 Instruction Manual
(14 pages)
(14 pages)
Power tools Delta 14-651 Instruction Manual
(15 pages)
(15 pages)
Power tools Delta AP300 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta GR350 Instruction Manual
(12 pages)
(12 pages)
Power tools Delta 32-326 User Manual
(4 pages)
Power tools Delta DP300 Instruction Manual
(17 pages)
(17 pages)
Power tools Delta 28-682 Instruction Manual
(20 pages)
(20 pages)
Power tools Delta 22-580 Instruction Manual
(21 pages)
(21 pages)
Power tools Delta 43-290C User Manual
(16 pages)
(16 pages)
Power tools Delta 28-206 Instruction Manual
(27 pages)
(27 pages)
Power tools Delta SA150 Instruction Manual
(12 pages)
(12 pages)
Power tools Delta 22-555 Use and Care Manual
(44 pages)
(44 pages)
Power tools Delta 14-651 Use and Care Manual
(43 pages)
(43 pages)
Power tools Delta SS350LS User Manual
(56 pages)
(56 pages)
GE DBSR463GGWW manuály
Uživatelské manuály a uživatelské příručky pro Sušičky GE DBSR463GGWW.
Poskytujeme 1 manuály pdf GE DBSR463GGWW ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comments to this Manuals