Delta N028314 Instruction Manual Page 24
- Page / 88
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
24
BEVEL RIPPING
Before connecting the table saw to the
power source or operating the saw, always inspect
the blade guard assembly and splitter for proper
alignment and clearance with saw blade. Check
alignment after each change of bevel angle.
When possible, place the fence on the
right side of the blade so that the blade is tilted away
from the fence and hands. Keep your hands clear of
the blade and use a pushstick to feed the workpiece if
there is less than 6" (152 mm) between the fence and
the blade.
Use caution when starting the cut to
prevent binding of the guard against the workpiece.
Bevel ripping (Fig. 56) is the same as ripping except the
bevel angle is set to an angle other than 0°.
To reduce the risk of injury, turn unit off
and disconnect it from power source before installing
and removing accessories, before adjusting or when
making repairs. An accidental start-up can cause injury.
The splitter and blade guard assemblies
cannot be used when dadoing. It must be removed as
described in Blade Guard and Splitter Use section. Use
EXTREME care when using the dado without the blade
guard assembly and splitter.
Use pushsticks, hold-downs, jigs,
fixtures or featherboards to help guide and control the
workpiece when the guard cannot be used.
Never use a molding cutterhead (A) Fig. 59
in a bevel position. Always use the proper molding
cutterhead throat plate (B).
Never run the stock between the fence
and the molding cutterhead. Irregular-shaped wood will
cause kickback.
To reduce the risk of injury, always return
and fasten the splitter and blade guard assemblies
to the proper operating position for normal through
sawing operations. Also, be sure the standard throat
plate is back in position.
USING A MOULDING CUTTERHEAD
Fig. 56
Fig. 57
Fig. 58
W
H
G
Give special attention to the grain direction. Make all cuts in the same direction as the grain whenever
possible.
Moulding is cutting a shape on the edge or face of the workpiece with a special moulding cutterhead.
The moulding head consists of a cutterhead in which can be mounted various shapes of steel knives (Fig. 57). Each of
the three knives in a set is fitted into a groove in the cutterhead and securely clamped with a screw. Keep the knife
grooves free of sawdust to allow the cutter to seating properly.
NOTE: The outside arbor flange cannot be used with the moulding cutterhead. Tighten the arbor nut against the cutterhead
body. Do not lose the outside arbor flange. It will be needed when reattaching a blade to the arbor.
1. You can easily attach a moulding cutterhead (A) Fig. 59 to the saw arbor. Also, you must use the accessory
moulding cutterhead throat plate (B) in place of the standard throat plate.
2. When using the moulding cutterhead, add wood-facing (C) to the face of the rip fence (Fig. 60). The wood-facing
is attached to the fence with wood screws through holes which must be drilled in the fence. Stock that is 3/4" (19
mm) inch thick is suitable for most work, although an occasional job may require 1" (25.4 mm) facing.
3. Position the wood-facing over the cutterhead with the cutterhead below the surface of the table. Turn the saw
on and raise the cutterhead. The cutterhead will cut its own groove in the wood-facing. Fig. 60 shows a typical
moulding operation.
To reduce the risk of injury, always return and fasten the splitter and blade guard assemblies to the proper
operating position for normal through sawing operations. Also, be sure the standard throat plate is back in position.
- Instruction Manual 1
- Manuel d’Utilisation 1
- Manual de Instrucciones 1
- TABLE OF CONTENTS 2
- IMPORTANT SAFETY INSTRUCTIONS 2
- GENERAL SAFETY RULES 3
- SAVE THESE INSTRUCTIONS 4
- TERMINOLOGY 5
- MAKING A PUSH STICK 5
- KICKBACKS 5
- POWER CONNECTIONS 6
- MOTOR SPECIFICATIONS 6
- GROUNDING INSTRUCTIONS 6
- FUNCTIONAL DESCRIPTION 8
- CARTON CONTENTS 9
- ASSEMBLY 10
- INSTALLING THE DRIVE BELT 11
- EXTENSION WINGS 12
- INSTALLING THE SWITCH 12
- ROUTING THE CORD 13
- INSTALLING THROAT PLATE 15
- ATTACHING A SAW BLADE 15
- ADJUSTING THROAT PLATE 16
- OPERATION 17
- ADJUSTING BLADE ALIGNMENT 18
- MITER GAUGE OPERATION 19
- MACHINE USE 20
- CROSS-CUTTING 21
- MAKING CUTS 21
- BEVEL CROSSCUTTING 22
- COMPOUND MITERING 22
- MITERING 22
- TOP VIEW 23
- BEVEL RIPPING 24
- USING A MOULDING CUTTERHEAD 24
- USING AN ACCESSORY DADO HEAD 25
- USING AUXILIARY WOOD FACING 26
- CONSTRUCTING A FEATHERBOARD 26
- PUSH STICK 27
- TROUBLESHOOTING 28
- MAINTENANCE 28
- ACCESSORIES 29
- WARRANTY 29
- CONSERVER CES DIRECTIVES 30
- RÈGLES DE SÉCURITÉ GÉNÉRALES 31
- TERMINOLOGIE 33
- RACCORDEMENTS ÉLECTRIQUES 34
- SPÉCIFICATIONS DU MOTEUR 34
- DESCRIPTION FONCTIONNELLE 36
- CONTENUS DE BOITE 37
- ASSEMBLAGE 38
- RALLONGES 40
- ACHEMINEMENT DU CORDON 41
- INSTALLATION DES PORTE-OUTILS 44
- ASSEMBLAGE DU GUIDE D’ONGLET 44
- FONCTIONNEMENT 45
- UTILISATION DU GUIDE D’ONGLET 47
- UTILISATION DE LA MACHINE 48
- TRONÇONNAGE 49
- COUPES LONGITUDINALES 50
- VUE EN PLAN 51
- SCIAGE SUR LE LONG EN BISEAU 52
- 19 mm (3/4 po) 54
- 114 mm (4-1/2 po) 54
- POUSSOIR 55
- DEPANNAGE 56
- ENTRETIEN 56
- ACCESSOIRIES 57
- GARANTIE 57
- GUARDE ESTAS INSTRUCCIONES 58
- NORMAS GENERALES DE SEGURIDAD 59
- TÉRMINOS 61
- FABRICANDO UNA VARA DE EMPUJE 61
- ESPECIFICACIONES DEL MOTOR 62
- DESCRIPCIÓN FUNCIONAL 64
- CONTENIDO DE CARTON 65
- ENSAMBLAJE 66
- BASES DE EXTENSIÓN 68
- INSTALACIÓN DEL INTERRUPTOR 68
- RECORRIDO DEL CABLE 69
- ACOPLE DE HOJA 71
- AJUSTE DEL INSERTO DE MESA 72
- OPERACIÓN 73
- UTILIZAR LA MAQUINA 76
- CORTE TRANSVERSAL 77
- CÓMO REALIZAR CORTES 77
- CORTE LONGITUDINAL 78
- VISIÓN SUPERIOR 79
- CORTE LONGITUDINAL CON BISEL 80
- 19 mm (3/4") 82
- 114 mm (4-1/2") 82
- CUADRADOS 83
- DE 12,7 MM (1/2”) 83
- SERVICIO 84
- LOCALIZACION DE FALLAS 84
- MANTENIMIENTO 84
- ACCESORIOS 85
- PÓLIZA DE GARANTÍA 85
- GARANTIA 86
Related products and manuals for Power tools Delta N028314
Power tools Delta 50-861 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 17-925 Instruction Manual
(20 pages)
(20 pages)
Power tools Delta 31-390 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 40 Instruction Manual
(14 pages)
(14 pages)
Power tools Delta TP305 Instruction Manual
(17 pages)
(17 pages)
Power tools Delta 40-570 Instruction Manual
(14 pages)
(14 pages)
Power tools Delta 40-650 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 31-120 Instruction Manual
(12 pages)
(12 pages)
Power tools Delta 23-840 Instruction Manual
(12 pages)
(12 pages)
Power tools Delta JT160 Instruction Manual
(21 pages)
(21 pages)
Power tools Delta GR150 Instruction Manual
(15 pages)
(15 pages)
Power tools Delta 50-770 Instruction Manual
(14 pages)
(14 pages)
Power tools Delta 14-651 Instruction Manual
(15 pages)
(15 pages)
(60 pages)
Power tools Delta AP300 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta GR350 Instruction Manual
(12 pages)
(12 pages)
GE DBSR463GGWW manuály
Uživatelské manuály a uživatelské příručky pro Sušičky GE DBSR463GGWW.
Poskytujeme 1 manuály pdf GE DBSR463GGWW ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comments to this Manuals