Delta N028314 Instruction Manual Page 7
- Page / 88
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
7
GROUNDED OUTLET BOX
CURRENT
CARRYING
PRONGS
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
GROUNDED OUTLET BOX
GROUNDING MEANS
ADAPTER
2. Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less
than 150 volts:
If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. A, the
machine will have a grounding plug that looks like the plug illustrated in Fig. A. A temporary adapter, which looks
like the adapter illustrated in Fig. B, may be used to connect this plug to a matching 2-conductor receptacle as
shown in Fig. B if a properly grounded outlet is not available. The temporary adapter should be used only until
a properly grounded outlet can be installed by a qualified electrician. The green-colored rigid ear, lug, and the
like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet
box. Whenever the adapter is used, it must be held in place with a metal screw.
NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.
In all cases, make certain that the receptacle in question is properly grounded. If you are not sure,
have a qualified electrician check the receptacle.
Fig. C
GROUNDED OUTLET BOX
CURRENT
CARRYING
PRONGS
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
3. 240 volt single phase operation:
The motor supplied with your machine is a dual voltage,
120/240 volt motor. It is shipped ready-to-run for 120
volt operation. However, it can be converted for 240 volt
operation.
A qualified electrician should do the conversion, or the
machine can be taken to an Authorized DELTA Service
Center. When completed, the machine must conform
to the National Electric Code and all local codes and
ordinances.
The machine is converted by re-wiring the motor for 240
volts, installing a 240 volt plug on the power supply cord
and replacing the switch (if necessary) with one that is
rated for 240 volt operation.
Be sure the 240 volt plug is only used in an outlet having
the same configuration as the plug illustrated in Fig. C.
No adapter should be used with the 240 volt plug.
In all cases, make certain that the
receptacle in question is properly grounded. If you
are not sure, have a qualified electrician check the
receptacle.
Fig. A Fig. B
- Instruction Manual 1
- Manuel d’Utilisation 1
- Manual de Instrucciones 1
- TABLE OF CONTENTS 2
- IMPORTANT SAFETY INSTRUCTIONS 2
- GENERAL SAFETY RULES 3
- SAVE THESE INSTRUCTIONS 4
- TERMINOLOGY 5
- MAKING A PUSH STICK 5
- KICKBACKS 5
- POWER CONNECTIONS 6
- MOTOR SPECIFICATIONS 6
- GROUNDING INSTRUCTIONS 6
- FUNCTIONAL DESCRIPTION 8
- CARTON CONTENTS 9
- ASSEMBLY 10
- INSTALLING THE DRIVE BELT 11
- EXTENSION WINGS 12
- INSTALLING THE SWITCH 12
- ROUTING THE CORD 13
- INSTALLING THROAT PLATE 15
- ATTACHING A SAW BLADE 15
- ADJUSTING THROAT PLATE 16
- OPERATION 17
- ADJUSTING BLADE ALIGNMENT 18
- MITER GAUGE OPERATION 19
- MACHINE USE 20
- CROSS-CUTTING 21
- MAKING CUTS 21
- BEVEL CROSSCUTTING 22
- COMPOUND MITERING 22
- MITERING 22
- TOP VIEW 23
- BEVEL RIPPING 24
- USING A MOULDING CUTTERHEAD 24
- USING AN ACCESSORY DADO HEAD 25
- USING AUXILIARY WOOD FACING 26
- CONSTRUCTING A FEATHERBOARD 26
- PUSH STICK 27
- TROUBLESHOOTING 28
- MAINTENANCE 28
- ACCESSORIES 29
- WARRANTY 29
- CONSERVER CES DIRECTIVES 30
- RÈGLES DE SÉCURITÉ GÉNÉRALES 31
- TERMINOLOGIE 33
- RACCORDEMENTS ÉLECTRIQUES 34
- SPÉCIFICATIONS DU MOTEUR 34
- DESCRIPTION FONCTIONNELLE 36
- CONTENUS DE BOITE 37
- ASSEMBLAGE 38
- RALLONGES 40
- ACHEMINEMENT DU CORDON 41
- INSTALLATION DES PORTE-OUTILS 44
- ASSEMBLAGE DU GUIDE D’ONGLET 44
- FONCTIONNEMENT 45
- UTILISATION DU GUIDE D’ONGLET 47
- UTILISATION DE LA MACHINE 48
- TRONÇONNAGE 49
- COUPES LONGITUDINALES 50
- VUE EN PLAN 51
- SCIAGE SUR LE LONG EN BISEAU 52
- 19 mm (3/4 po) 54
- 114 mm (4-1/2 po) 54
- POUSSOIR 55
- DEPANNAGE 56
- ENTRETIEN 56
- ACCESSOIRIES 57
- GARANTIE 57
- GUARDE ESTAS INSTRUCCIONES 58
- NORMAS GENERALES DE SEGURIDAD 59
- TÉRMINOS 61
- FABRICANDO UNA VARA DE EMPUJE 61
- ESPECIFICACIONES DEL MOTOR 62
- DESCRIPCIÓN FUNCIONAL 64
- CONTENIDO DE CARTON 65
- ENSAMBLAJE 66
- BASES DE EXTENSIÓN 68
- INSTALACIÓN DEL INTERRUPTOR 68
- RECORRIDO DEL CABLE 69
- ACOPLE DE HOJA 71
- AJUSTE DEL INSERTO DE MESA 72
- OPERACIÓN 73
- UTILIZAR LA MAQUINA 76
- CORTE TRANSVERSAL 77
- CÓMO REALIZAR CORTES 77
- CORTE LONGITUDINAL 78
- VISIÓN SUPERIOR 79
- CORTE LONGITUDINAL CON BISEL 80
- 19 mm (3/4") 82
- 114 mm (4-1/2") 82
- CUADRADOS 83
- DE 12,7 MM (1/2”) 83
- SERVICIO 84
- LOCALIZACION DE FALLAS 84
- MANTENIMIENTO 84
- ACCESORIOS 85
- PÓLIZA DE GARANTÍA 85
- GARANTIA 86
Related products and manuals for Power tools Delta N028314
Power tools Delta 50-861 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 17-925 Instruction Manual
(20 pages)
(20 pages)
Power tools Delta 31-390 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 40 Instruction Manual
(14 pages)
(14 pages)
Power tools Delta TP305 Instruction Manual
(17 pages)
(17 pages)
Power tools Delta 40-570 Instruction Manual
(14 pages)
(14 pages)
Power tools Delta 40-650 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 31-120 Instruction Manual
(12 pages)
(12 pages)
Power tools Delta 23-840 Instruction Manual
(12 pages)
(12 pages)
Power tools Delta JT160 Instruction Manual
(21 pages)
(21 pages)
Power tools Delta GR150 Instruction Manual
(15 pages)
(15 pages)
Power tools Delta 50-770 Instruction Manual
(14 pages)
(14 pages)
Power tools Delta 14-651 Instruction Manual
(15 pages)
(15 pages)
(60 pages)
Power tools Delta AP300 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta GR350 Instruction Manual
(12 pages)
(12 pages)
© 2020, manymanuals.com. All rights reserved. | 0.293 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals