Delta 70-200 User Manual download pdf (Page 2)

SAFETY RULES

Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain

hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possi-

bility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result.

Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles, dust masks and hearing protection can reduce

your potential for injury. But even the best guard won’t make up for poor judgment, carelessness or inattention. Always use com

mon sense and exercise caution in the workshop. If a procedure feels dangerous, don’t try it. Figure out an alternative procedure

that feels safer. REMEMBER: Your personal safety is your responsibility.

This machine was designed for certain applications only. Delta Machinery strongly recommends that this machine not be modified

and/or used for any application other than that for which it was designed. If you have any questions relative to a particular applica-

tion, DO NOT use the machine until you have first contacted Delta to determine if it can or should be performed on the product.

Technical Service Manager

Delta Machinery

4825 Highway 45 North

Jackson, TN 38305

(IN CANADA: 505 SOUTHGATE DRIVE, GUELPH, ONTARIO N1H 6M7)

WARNING: FAILURE TO FOLLOW THESE RULES

MAY RESULT IN SERIOUS PERSONAL INJURY

1. FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL

BEFORE OPERATING THE TOOL. Learn the tool’s application

and limitations as well as the specific hazards peculiar to it.

2. KEEP GUARDS IN PLACE and in working order.

3. ALWAYS WEAR EYE PROTECTION.

4. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit

of checking to see that keys and adjusting wrenches are removed

from tool before turning it “on”.

5. KEEP WORK AREA CLEAN. Cluttered areas and benches

invite accidents.

6. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use

power tools in damp or wet locations, or expose them to rain.

Keep work area well-lighted.

7. KEEP CHILDREN AND VISITORS AWAY. All children and

visitors should be kept a safe distance from work area.

8. MAKE WORKSHOP CHILDPROOF – with padlocks, master

switches, or by removing starter keys.

9. DON’T FORCE TOOL. It will do the job better and be safer at

the rate for which it was designed.

10. USE RIGHT TOOL. Don’t force tool or attachment to do a job

for which it was not designed.

11. WEAR PROPER APPAREL. No loose clothing, gloves, neck-

ties, rings, bracelets, or other jewelry to get caught in moving

parts. Nonslip footwear is recommended. Wear protective hair

covering to contain long hair.

12.

ALWAYS USE SAFETY GLASSES.

Wear safety glasses.

Everyday eyeglasses only have impact resistant lenses; they

are not safety glasses. Also use face or dust mask if cutting

operation is dusty. These safety glasses must conform to ANSI

Z87.1 requirements. Note: Approved glasses have Z87 printed

or stamped on them.

13. SECURE WORK. Use clamps or a vise to hold work when

practical. It’s safer than using your hand and frees both hands to

operate tool.

14. DON’T OVERREACH. Keep proper footing and balance at all

times.

15. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp

and clean for best and safest performance. Follow instructions for

lubricating and changing accessories.

16. DISCONNECT TOOLS before servicing and when changing

accessories such as blades, bits, cutters, etc.

17. USE RECOMMENDED ACCESSORIES. The use of acces-

sories and attachments not recommended by Delta may cause

hazards or risk of injury to persons.

18. REDUCE THE RISK OF UNINTENTIONAL STARTING.

Make sure switch is in “OFF” position before plugging in power

cord.

19. NEVER STAND ON TOOL. Serious injury could occur if the

tool is tipped or if the cutting tool is accidentally contacted.

20. CHECK DAMAGED PARTS. Before further use of the tool, a

guard or other part that is damaged should be carefully checked

to ensure that it will operate properly and perform its intended

function – check for alignment of moving parts, binding of moving

parts, breakage of parts, mounting, and any other conditions that

may affect its operation. A guard or other part that is damaged

should be properly repaired or replaced.

21. DIRECTION OF FEED. Feed work into a blade or cutter

against the direction of rotation of the blade or cutter only.

22. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN

POWER OFF. Don’t leave tool until it comes to a complete stop.

23. DRUGS, ALCOHOL, MEDICATION. Do not operate tool

while under the influence of drugs, alcohol or any medication.

24. MAKE SURE TOOL IS DISCONNECTED FROM POWER

SUPPLY while motor is being mounted, connected or re-

connected.

25. THE DUST GENERATED by certain woods and wood prod-

ucts can be injurious to your health. Always operate machinery in

well ventilated areas and provide for proper dust removal. Use

wood dust collection systems whenever possible.

26.

WARNING: SOME DUST CREATED BY POWER

SANDING, SAWING, GRINDING, DRILLING, AND OTHER

CONSTRUCTION ACTIVITIES contains chemicals known to

cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often

you do this type of work. To reduce your exposure to these

chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are

specially designed to filter out microscopic particles.

SAVE THESE INSTRUCTIONS

1 2 3 ... 17

Comments to this Manuals

No comments

Delta 70-200 User Manual Page 2

Comments to this Manuals

Related products and manuals for Tools Delta 70-200