Delta 70-200 User Manual download pdf (Page 4)

CONNECTING DRILL PRESS TO POWER SOURCE

POWER CONNECTIONS

A separate electrical circuit should be used for your tools. This circuit should not be less than #12 wire and should be

protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-

prong grounding type plugs and 3-pole receptacles which accept the tool’s plug. Before connecting the motor to the

power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the same charac-

teristics as indicated on the tool. All line connections should make good contact. Running on low voltage will dam-

age the motor.

MOTOR SPECIFICATIONS

Your drill press is designed to use a 1720 RPM motor. It is wired at the factory for 110-120 Volts, 60 Hz alternating cur-

rent. Never use a motor that runs faster than 1720 RPM. Your drill press may be converted for 220-240 volt operation.

The conversion of your drill press for 220-240 volt operation must be done by qualified electrical personnel.

GROUNDING INSTRUCTIONS

WARNING: THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM

ELECTRIC SHOCK.

2. Grounded, cord-connected tools intended for use on

a supply circuit having a nominal rating less than 150

volts:

This tool is intended for use on a normal 120-volt circuit

and has a grounded plug that looks like the plug illustrat-

ed in Fig. A.

If a properly grounded outlet is not available, a temporary

adapter, shown in Fig. B, may be used for connecting the

3-prong grounding type plug to a 2-prong receptacle. The

temporary adapter should be used only until a properly

grounded outlet can be installed by a qualified electrician.

The green colored rigid ear, lug, or the like extending from

the adapter must be connected to a permanent ground

such as a properly grounded outlet box cover. Whenever

the adapter is used, it must be held in place with a metal

screw.

NOTE: In Canada, the use of a temporary adapter is

not permitted by the Canadian Electric Code.

1. All grounded, cord-connected tools: In the event of a

malfunction or breakdown, grounding provides a path of

least resistance for electric current to reduce the risk of

electric shock. This tool is equipped with an electric cord

having an equipment-grounding conductor and a ground-

ing plug. The plug must be plugged into a matching out-

let that is properly installed and grounded in accordance

with all local codes and ordinances.

Do not modify the plug provided - if it will not fit the out-

let, have the proper outlet installed by a qualified electri-

cian.

Improper connection of the equipment-grounding con-

ductor can result in risk of electric shock. The conductor

with insulation having an outer surface that is green with

or without yellow stripes is the equipment-grounding con-

ductor. If repair or replacement of the electric cord or plug

is necessary, do not connect the equipment grounding

conductor to a live terminal.

Check with a qualified electrician or service personnel if

the grounding instructions are not completely under-

stood, or if in doubt as to whether the tool is properly

grounded.

Use only 3-wire extension cords that have 3-prong

grounding type plugs and 3-hole receptacles that accept

the tool’s plug, as shown in Fig. A.

Repair or replace damaged or worn cord immediately.

3. Grounded, cord-connected tools intended for use on

a supply circuit having a nominal rating between 150 -

250 volts, inclusive:

This tool is intended for use on a circuit that has an out-

let that looks like the one illustrated in Fig. C. The tool

has a grounding plug that looks like the plug illustrated

in Fig. C. Make sure the tool is connected to an outlet

having the same configuration as the plug. No adapter is

available or should be used with this tool. If the tool

must be reconnected for use on a different type of elec-

tric circuit, the reconnection should be made by quali-

fied service personnel; and after reconnection, the tool

should comply with all local codes and ordinances.

WARNING: IN ALL CASES, MAKE CERTAIN THE

RECEPTACLE IN QUESTION IS PROPERLY

GROUNDED. IF YOU ARE NOT SURE HAVE A CERTI-

FIED ELECTRICIAN CHECK THE RECEPTACLE.

1 2 3 4 5 ... 17

Comments to this Manuals

No comments

Delta 70-200 User Manual Page 4

Comments to this Manuals

Related products and manuals for Tools Delta 70-200