Delta 22-790X Instruction Manual Page 17
- Page / 72
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
17
HOW TO SET A KNIFE
clockwise to raise the knife on each end of the cutterhead
against the knife slot.
IMPORTANT: Tighten the knife in the slot only enough
to hold it in position.
the center screws until the knife is secure. Tighten the other knives in the same manner.
IMPORTANT: After the knives have been ad just ed, re place the chip deflector that was removed in STEP 3 and the top
cover that was removed in STEP 1 (under How to Check, Adjust and Replace Knives.) Pivot the motor assembly
back to its original place.
Use a gauge block to check and adjust the height of the
chipbreaker and the infeed and outfeed roll. Adjust the
cutterhead parallel to the table. Construct a gauge block
from hard wood using the dimensions in Fig. 47.
Fig. 45
L
H
N
K
HOW TO CLEAN AND CHECK THE KNIVES
Wear gloves when you remove the knives for sharpening or replacement. The knives are very
sharp.
Disconnect the machine from the power source.
this process for the other knives, locking bars,
and locking screws.
B. Thoroughly clean the knives, knife slots, locking
bars, and locking screws. If the threads of the
screws appear worn or stripped, or if the heads
are becoming rounded, replace them.
C. Insert the locking bars, knives, and screws in all
three slots in the cutterhead. Loosen the locking
enough to hold all three knives in the cutterhead.
D. Adjust all three knives as explained under STEP 4.
HOW TO CONSTRUCT THE GAUGE BLOCK
Fig. 46
H
N
Fig. 47
4"
1/2"
4"
mm)
3"
K
- Instruction manual 1
- Manuel d’utilisation 1
- Manual de instrucciones 1
- TABLE OF CONTENTS 2
- IMPORTANT SAFETY INSTRUCTIONS 2
- GENERAL SAFETY RULES 3
- SAVE THESE INSTRUCTIONS 4
- GROUNDING INSTRUCTIONS 5
- EXTENSION CORDS 5
- FUNCTIONAL DESCRIPTION 6
- CARTON CONTENTS 6
- STAND PARTS 7
- ROLLER TABLE PARTS 7
- ASSEMBLY 8
- ATTACHING LEVELING FEET 9
- ATTACHING HANDWHEEL 9
- HOW TO LIFT THE MACHINE 10
- HOW TO SECURE THE POWER CORD 10
- TABLES TO THE STAND 12
- HOW TO CONTROL THE FEED SPEED 15
- HOW TO ADJUST BELT TENSION 15
- HOW TO SET A KNIFE 17
- TROUBLESHOOTING 21
- MAINTENANCE 21
- LUBRICATION OF GEARS 22
- ACCESSORIES 23
- WARRANTY 24
- RÈGLES DE SÉCURITÉ GÉNÉRALES 26
- CONSERVER CES DIRECTIVES 27
- RACCORDEMENTS ÉLECTRIQUES 27
- SPÉCIFICATIONS DU MOTEUR 27
- CORDON DE RALLONGE 28
- DESCRIPTION FONCTIONNELLE 29
- CONTENUS DE BOITE 29
- PIÈCES DU SOCLE 30
- COMPOSANTS DE LA RALLONGE À 30
- ROULEAUX 30
- ASSEMBLAGE 31
- CAPOT À POUSSIÈRE 33
- DÉMARRAGE ET ARRÊT DE MACHINE 37
- RÉGLAGE DE COUTEAU 40
- CONSTRUIRE LE BLOC-JAUGE 40
- DEPANNAGE 44
- ENTRETIEN 44
- DÉMARRAGE IMPOSSIBLE 45
- ACCESSOIRIES 46
- GARANTIE 47
- NORMAS GENERALES DE SEGURIDAD 49
- GUARDE ESTAS INSTRUCCIONES 50
- CORDONES DE EXTENSIÓN 51
- DESCRIPCIÓN FUNCIONAL 52
- CONTENIDO DE CARTON 52
- PIEZAS DE LA BASE 53
- PIEZAS DE LA MESA DEL RODILLO 53
- ENSAMBLAJE 54
- CÓMO FIJAR LA BASE DE LA 55
- CEPILLADORA AL PISO 55
- CÓMO INSTALAR EL VOLANTE 55
- LA CUBIERTA PARA POLVO 56
- CÓMO LEVANTAR LA MÁQUINA 56
- RODILLO A LA BASE 58
- DEL RODILLO 59
- CÓMO CALIBRAR UNA CUCHILLA 63
- LOCALIZACION DE FALLAS 67
- MANTENIMIENTO 68
- SERVICIO 69
- ACCESORIOS 70
- PÓLIZA DE GARANTÍA 70
- GARANTIA 70
- MODEL 22-790X 71
Related products and manuals for Power planers Delta 22-790X
(20 pages)
(188 pages)© 2020, manymanuals.com. All rights reserved. | 2.102 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals