Delta 36-325C Instruction Manual download pdf (Page 3)

ADDITIONAL SAFETY RULES

FOR TABLE SAWS

1. DO NOT OPERATE YOUR TOOL until it is

completely assembled and installed according to the

instructions.

2. IF YOU ARE NOT thoroughly familiar with the opera-

tion of circular saws, obtain advice from your supervisor,

instructor, or other qualified person.

3. ALWAYS use guard, splitter and anti-kickback fingers

on all “thru-sawing” operations. Thru-sawing operations

are those when the blade cuts completely through the

workpiece as in ripping or cross-cutting.

4. ALWAYS hold the work firmly against the miter gage

or fence.

5. NEVER use the fence as a cut-off gage when cross-

cutting.

6. MOVE the rip fence out of the way when cross-

cutting.

7. NEVER perform any operation “free-hand” which

means using your hands to support or guide the

workpiece. Always use either the fence or miter gage to

position and guide the work.

8. ALWAYS use a push stick for ripping narrow stock.

Refer to ripping applications in instruction manual where

the push stick is covered in detail.

9. AVOID kickbacks (work thrown back toward you) by:

A. Keeping blade sharp.

B. Keeping rip fence parallel to the saw blade.

C. Keeping splitter and anti-kickback fingers and

guard in place and operating.

D. Not releasing the work before it is pushed all the

way past the saw blade.

E. Not ripping work that is twisted or warped or

does not have a straight edge to guide along

the fence.

10. AVOID awkward operations and hand positions

where a sudden slip could cause your hand to move into

the cutting tool.

11. ALWAYS keep hands and fingers away from the

cutting tool.

12. NEVER stand or have any part of your body in line

with the path of the saw blade.

13. NEVER reach behind or over the cutting tool with

either hand for any reason.

14. DIRECTION OF FEED. Feed work into cutting tool

against the direction or rotation of the cutting tool only.

15. DO NOT feed the material too fast while cutting.

Feed the material only fast enough so that the blade will

cut.

16. NEVER attempt to free a stalled saw blade without

first turning the saw “OFF.”

17. NEVER start the saw with the workpiece pressed

against the blade.

18. NEVER turn the saw “ON” before clearing the table

of all objects (tools, scraps of wood, etc.).

19. ALWAYS STOP the saw before removing scrap

pieces from the table.

20. NEVER perform layout, assembly or set-up work on

the table while the saw is operating.

21. PROVIDE adequate support to the rear and sides of

the saw table for wide or long workpieces.

22. WHEN cutting mouldings, NEVER run the stock

between the fence and the moulding cutterhead.

23. NEVER use solvents to clean plastic parts. Solvents

could possibly dissolve or otherwise damage the material.

Only a soft damp cloth should be used to clean plastic

parts.

24. SHOULD any part of your tool be missing, damaged,

or fail in any way, or any electrical components fail to

perform properly, shut off tool and remove plug from

power supply outlet. Replace missing, damaged or failed

parts before resuming operation.

25. IMPORTANT: When the tool is not in use, the

switch should be locked in the “OFF” position to

prevent unauthorized use.

26. ADDITIONAL INFORMATION regarding the safe

and proper operation of this product is available from the

National Safety Council, 1121 Spring Lake Drive, Itasca,

IL 60143-3201, in the Accident Prevention Manual for

Industrial Operations and also in the Safety Data Sheets

provided by the NSC. Please also refer to the American

National Standards Institute ANSI 01.1 Safety

Requirements for Woodworking Machinery and the U.S.

Department of Labor OSHA 1910.213 Regulations.

1 2 3 4 5 6 7 8 ... 27 28

Comments to this Manuals

No comments

Delta 36-325C Instruction Manual Page 3

Comments to this Manuals

Related products and manuals for Circular saws Delta 36-325C