Delta 22-785 Instruction Manual

Browse online or download Instruction Manual for Knives Delta 22-785. Delta 22-785 Instruction manual User Manual

  • Download
  • Add to my manuals
  • Print

Summary of Contents

Page 1 - 15" Planer

INSTRUCTION MANUAL15" Planer(Model 22-785)(Model 22-785X)PART NO. 909593 - 06-07-05Copyright © 2005 Delta MachineryTo learn more about DELTA MACH

Page 2 - IMPORTANT SAFETY INSTRUCTIONS

10ASSEMBLING TOP COVER ANDDUST CHUTE1. Fasten the top cover and dust chute (A) Fig. 16, tothe top of the planer, as shown, using the threeM6x16mm scre

Page 3 - CALIFORNIA PROPOSITION 65

11DEPTH OF CUT ADJUSTMENTThe depth of cut on your planer is controlled by raisingor lowering the head assembly (A) Fig. 22, whichcontains the cutterhe

Page 4 - GENERAL SAFETY RULES

12ANTI-KICKBACK FINGERSWHEN INSPECTING AND CLEANINGTHE ANTI-KICKBACK FINGERS, MAKESURE THE MACHINE IS DISCONNECTED FROM THEPOWER SOURCE.A series of an

Page 5 - SAVE THESE INSTRUCTIONS

13Fig. 324. Remove the three screws (E) Fig. 34, and remove thechip deflector (F).5. To check and adjust the knives, proceed as follows:A. Carefully p

Page 6 - GROUNDING INSTRUCTIONS

14CONSTRUCTINGGAGE BLOCKIn order to check and adjust the height of thechipbreaker, infeed and outfeed roll and adjust thecutterhead parallel to the ta

Page 7 - CARTON CONTENTS

15ADJUSTING HEIGHTOF INFEED ROLLERThe infeed roller is adjusted at the factory at 0.040"below the cutting circle. To check and adjust theheight o

Page 8 - ASSEMBLY

16ADJUSTING SPRING TENSION OFINFEED AND OUTFEED ROLLERSThe infeed and outfeed rollers are those parts of yourplaner that feed the stock while it is be

Page 9 - LIFTING THE MACHINE

17ADJUSTING CUTTINGHEADPARALLEL TO TABLEThe cuttinghead is set parallel to the table at the factoryand no further adjustment should be necessary. If y

Page 10 - POSITION

MAINTENANCEFig. 53 Fig. 54ABFig. 55ECDFig. 56FLUBRICATIONThe gear box oil should be changed once a year. Useextreme pressure gear oil, available from

Page 11 - FEED SPEED CONTROL

19KEEP MACHINE CLEANPeriodically blow out all air passages with dry compressedair. All plastic parts should be cleaned with a soft dampcloth. NEVER us

Page 12 - ANTI-KICKBACK FINGERS

2TABLE OF CONTENTSRead and understand all warnings and operating instructions before using any tool or equipment. Whenusing tools or equipment, basic

Page 13

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marquessuivantes sont de

Page 14 - OF CHIPBREAKER

3Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

Page 15 - OF OUTFEED ROLLER

4GENERAL SAFETY RULESREAD AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFOREUSING THIS EQUIPMENT. Failure to follow all instructions listed

Page 16 - ADJUSTING TABLE ROLLERS

5FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.ADDITIONAL SPECIFIC SAFETY RULESSAVE THESE INSTRUCTIONS. Refer to them often and

Page 17 - PARALLEL TO TABLE

6Fig. AGROUNDED OUTLET BOXCURRENTCARRYINGPRONGSGROUNDING BLADEIS LONGEST OF THE 3 BLADESPOWER CONNECTIONSMOTOR SPECIFICATIONSGROUNDING INSTRUCTIONS3.

Page 18 - TROUBLESHOOTING

7FOREWORDDelta Models 22-785 and 22-785X are 15" (381mm) Planers with adjustable feed rate for optimum planing under load.They have the following

Page 19 - WARRANTY

81 - Top cover2 - Cord clamp3 - Knife setting gage4 - Open end wrench (14 and 17mm)5 - Open end wrench (10 and 12mm)6 - M6x1x16mm hex flange screw (4)

Page 20 - • DELTA)

9CUTTINGHEAD RAISING ANDLOWERING HANDWHEEL1. Insert key (A) Fig. 7, into keyway (B) of raising andlowering shaft.Fig. 7Fig. 82. Assemble handwheel (C)

Comments to this Manuals

No comments