Delta 36-R53 Instruction Manual download pdf (Page 7)

UNPACKING AND CLEANING

Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from

all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone,

gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household

floor paste wax.

REMOVE THE STYROFOAM PACKING AND ANY OTHER LOOSE ITEMS FROM THE INSIDE OF THE

SAW CABINET. THE MOTOR COVER MUST BE REMOVED IN ORDER TO REMOVE ITEMS FROM INSIDE THE SAW

CABINET. TO REMOVE THE MOTOR COVER, REMOVE THE 1/4-20x5/8" HEX HEAD SCREW FROM LOCATION

(B) FIG. 1, AND PUSH MOTOR COVER TO ONE SIDE TO DEPRESS CLIPS, AND PULL MOTOR COVER OFF. SEE

SECTION “MOTOR COVER”.

IMPORTANT: The saw is shipped with the saw arbor in the 45 degree position. NOTE: THE HAND WHEEL MUST BE

ASSEMBLED TO THE SAW, SEE THE SECTION “BLADE TILTING HANDWHEEL”, THEN PROCEED WITH THE

FOLLOWING. Loosen locking knob on the handwheel, and turn handwheel until the saw arbor is in the 90 degree

position and remove the styrofoam packing from inside the saw cabinet. Tighten locking knob.

UNISAW PARTS

4 5

Fig. 1

Fig. 2

Fig. 1

1. Unisaw

2. Switch (shown with a GPE switch)

Fig. 2

3. Extension wing (2)

4. Handwheel

5. Blade guard and splitter assembly

6. Upper bracket for splitter

7. Lower bracket for support rod

8. Support rod

9. 7/8" Open end arbor wrench

10. 7/8"x1/2" Closed end arbor wrench

11. Dust chute

12. Miter gage

13. Cap for miter gage handle

14. Handle for miter gage

15. Handwheel lock knob

16. 1/8" Hex wrench

17. 5/64" Hex wrench

18. Hanger for rip fence (2)

19. 7/16-20x1¼" Hex head screw (6)

20. 5/16-18x1" Hex head screw (4)

21. 5/16-18x1" Flat Head Screw (1)

22. #10x1/2" Hex washer head screw (8)

23. 10-32x1/2" Pan head screw (2) ( for use w/ LVC models only)

24. 3/4" I.D. Fiber washer (1)

25. 5/8" I.D. Internal tooth washer (1)

26. 7/16" I.D. Flat washer (6)

27. 5/16" I.D. Flat washer (2)

28. 5/16" I.D. Flat washer (1) (for use w/ GPE models only)

29. 5/16" I.D. Lockwasher (3)

30. 1/4" I.D. Fiber washer (1)

31. 13/64" I.D. Flat washer (2) (for use w/ LVC models only)

32. 5/8-18 Jam nut (1)

33. 5/16-18 Hex nut (1) (for use w/ GPE models only)

34. 1-3/8" Key (1)

35. Spring clip (2) (for use w/ LVC models only)

1 2 3 4 5 6 7 8 9 10 11 12 ... 27 28

Comments to this Manuals

No comments

Delta 36-R53 Instruction Manual Page 7

Comments to this Manuals

Related products and manuals for Mitre saws Delta 36-R53