Delta 28-190 Instruction Manual download pdf (Page 3)

SAFETY RULES

Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are

certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably

lessen the possiblity of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the

operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles, dust masks and

hearing protection can reduce your potential for injury. But even the best guard won’t make up for poor judgment,

carelessness or inattention. Always use common sense

and exercise caution in the workshop. If a procedure feels dangerous,

don’t try it. Figure out an alternative procedure that feels safer. REMEMBER: Your personal safety is your responsibility.

This machine was designed for certain applications only. Delta Machinery strongly recommends that this machine not be

modified and/or used for any application other than that for which it was designed. If you have any questions relative to a

particular application, DO NOT use the machine until you have first contacted Delta to determine if it can or should be

performed on the product.

DELTA INTERNATIONAL MACHINERY CORP.

MANAGER OF TECHNICAL SERVICES

246 ALPHA DRIVE

PITTSBURGH, PENNSYLVANIA 15238

(IN CANADA: 644 IMPERIAL ROAD, GUELPH, ONTARIO N1H 6M7)

1. FOR YOUR OWN SAFETY, READ INSTRUCTION

MANUAL BEFORE OPERATING THE TOOL. Learn the

tool's application and limitations as well as the specific

hazards peculiar to it.

2. KEEP GUARDS IN PLACE and in working order.

3. ALWAYS WEAR EYE PROTECTION.

4. GROUND ALL TOOLS. If tool is equipped with three-

prong plug, it should be plugged into a three-hole electrical

receptacle. If an adapter is used to accommodate a two-

prong receptacle, the adapter lug must be attached to a

known ground. Never remove the third prong.

5. REMOVE ADJUSTING KEYS AND WRENCHES. Form

habit of checking to see that keys and adjusting wrenches

are removed from tool before turning it “on.”

6. KEEP WORK AREA CLEAN. Cluttered areas and

benches invite accidents.

7. DON'T USE IN DANGEROUS ENVIRONMENT. Don't

use power tools in damp or wet locations, or expose them

to rain. Keep work area well-lighted.

8. KEEP CHILDREN AND VISITORS AWAY. All children

and visitors should be kept a safe distance from work area.

9. MAKE WORKSHOP CHILDPROOF - with padlocks,

master switches, or by removing starter keys.

10. DON'T FORCE TOOL. It will do the job better and be

safer at the rate for which it was designed.

11. USE RIGHT TOOL. Don't force tool or attachment to

do a job for which it was not designed.

12. WEAR PROPER APPAREL. No loose clothing, gloves,

neckties, rings, bracelets, or other jewelry to get caught in

moving parts. Nonslip footwear is recommended. Wear

protective hair covering to contain long hair.

13. ALWAYS USE SAFETY GLASSES. Wear safety glasses

(must comply with ANSI Z87.1). Everyday eyeglasses only

have impact resistant lenses; they are not safety glasses.

Also use face or dust mask if cutting operation is dusty.

14. SECURE WORK. Use clamps or a vise to hold work

when practical. It's safer than using your hand and frees

both hands to operate tool.

15. DON'T OVERREACH. Keep proper footing and

balance at all times.

16. MAINTAIN TOOLS IN TOP CONDITION. Keep tools

sharp and clean for best and safest performance. Follow

instructions for lubricating and changing accessories.

17. DISCONNECT TOOLS before servicing and when

changing accessories such as blades, bits, cutters, etc.

18. USE RECOMMENDED ACCESSORIES. The use of

improper accessories may cause hazards or risk of injury to

persons.

19. REDUCE THE RISK OF UNINTENTIONAL START-

ING. Make sure switch is in “OFF” position before plugging

in power cord.

20. NEVER STAND ON TOOL. Serious injury could occur if

the tool is tipped or if the cutting tool is accidentally

contacted.

21. CHECK DAMAGED PARTS. Before further use of the

tool, a guard or other part that is damaged should be

carefully checked to ensure that it will operate properly and

perform its intended function - check for alignment of

moving parts, binding of moving parts, breakage of parts,

mounting, and any other conditions that may affect its

operation. A guard or other part that is damaged should be

properly repaired or replaced.

22. DIRECTION OF FEED. Feed work into a blade or

cuttter against the direction of rotation of the blade or cutter

only.

23. NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Don't leave tool until it comes to a

complete stop.

24. DRUGS, ALCOHOL, MEDICATION. Do not operate

tool while under the influence of drugs, alcohol or any

medication.

25. MAKE SURE TOOL IS DISCONNECTED FROM

POWER SUPPLY while motor is being mounted, connected

or reconnected.

26. WARNING: The dust generated by certain woods and

wood products can be injurious to your health. Always

operate machinery in well ventilated areas and provide for

proper dust removal. Use wood dust collection systems

whenever possible.

WARNING: FAILURE TO FOLLOW THESE RULES

MAY RESULT IN SERIOUS PERSONAL INJURY

1 2 3 4 5 6 7 8 ... 17 18

Comments to this Manuals

No comments

Delta 28-190 Instruction Manual Page 3

Comments to this Manuals

Related products and manuals for Power tools Delta 28-190