Delta 28-299A Operations Instructions Page 45
- Page / 77
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
6.4 Displays
The LCP displays a wide range of performance information
about the soft starter. Press the S
STATUS
button to access the
status display screens, then use the
Ⴃ
and
Ⴍ
buttons to select
the information to display. To return to the status screens
from within a menu, press the B
BACK
button repeatedly or
press the S
STATUS
button.
•
Temperature monitoring
•
Programmable screen (see Par. 8-2 - 8-5)
•
Current
•
Frequency
•
Motor power
•
Last start information
•
Date and time
•
SCR Conduction bar-graph
•
Performance graphs
NOTE
Screens shown here are with the default settings.
6.4.1 Temperature Monitoring Screen (S1)
The temperature screen shows the temperature of the motor
as a percentage of total thermal capacity, and also shows
which motor data set is in use.
The temperature monitoring screen is the default status
screen.
Ready S1
MS1 000.0A 000.0kW
Primary Motor Set
M1 000%
6.4.2 Programmable Screen (S2)
The MCD 500's user-programmable screen can be configured
to show the most important information for the particular
application. Use parameters 8-2 to 8-5 to select which
information to display.
Ready S2
MS1 000.0A 000.0kW
-.-- pf
00000 hrs
6.4.3 Average Current (S3)
The average current screen shows the average current of all
three phases.
Ready S3
MS1 000.0A 000.0kW
0.0A
6.4.4 Current Monitoring Screen (S4)
The current screen shows real-time line current on each
phase.
Ready S4
MS1 000.0A 000.0kW
Phase currents
000.0A 000.0A 000.0A
6.4.5 Frequency Monitoring Screen (S5)
The frequency screen shows the mains frequency as
measured by the soft starter.
Ready S5
MS1 000.0A 000.0kW
00.0Hz
6.4.6 Motor Power Screen (S6)
The motor power screen shows motor power (kW, HP and
kVA) and power factor.
Ready S6
MS1 000.0A 000.0kW
000.0kW 0000HP
0000kVA -. - - pf
6.4.7 Last Start Information (S7)
The last start information screen shows details of the most
recent successful start:
•
start duration (seconds)
•
maximum start current drawn (as a percentage of
motor full load current)
•
calculated rise in motor temperature
Ready S7
MS1 000.0A 000.0kW
Last start 000 s
000 % FLC
˂Temp 0%
Operation MCD 500 Operating Instruction
44 MG.17.K3.02 - VLT
®
is a registered Danfoss trademark
66
- Operating Instructions 1
- MG.17.K3.02 - VLT 2
- 5 Application Examples 3
- 6 Operation 3
- 7 Programming 4
- 9 Troubleshooting 5
- 10 Specifications 5
- 1 Safety 6
- 2 Introduction 7
- 177HA382.11 8
- 3 Installation 9
- 177HA514.10 10
- 4 Electrical Installation 11
- 4.1.3 Remote Inputs 12
- 4.1.4 Serial Communication 12
- 4.1.5 Earth Terminal 12
- 177HA542.11 13
- 4.1.7 Motor Connection 14
- 4.2 In-Line Installation 14
- 177 HA4 31.11 15
- 177HA500.11 16
- 4.4 Current Ratings 17
- Start Time (seconds) 19
- Starts Per Hour 19
- 4.6 Bypass Contactor 22
- 4.7 Main Contactor 22
- 4.8 Circuit Breaker 22
- 4.9 Power Factor Correction 22
- 4.10 Fuses 23
- 4.10.1 Power Supply Fuses 23
- 4.10.4 Ferraz Fuses - HSJ 25
- 4.11 Schematic Diagrams 28
- 177HA426.11 29
- 5.3 Starting Modes 31
- 5.3.1 Constant Current 31
- 5.3.2 Current Ramp 31
- Voltage (% full voltage) 32
- 177HA511.10 33
- 5.6 Inside Delta Operation 34
- 5.7 Typical Start Currents 34
- 177HA522.10 36
- 177HA523.10 37
- 5.10 Emergency Run Operation 38
- 5.11 Auxiliary Trip Circuit 39
- 5.12 Soft Braking 40
- 5.13 Two Speed Motor 41
- 6.2 Control Methods 44
- 6.3 Local Control Buttons 44
- 6.4.8 Date and Time (S8) 46
- 6.4.9 SCR Conduction Bargraph 46
- 6.4.10 Performance Graphs 46
- 7.2 Quick Menu 48
- 7.2.1 Quick Setup 48
- 7.2.2 Application Setups 49
- 7.2.3 Loggings 50
- 7.3 Main Menu 50
- 7.3.1 Parameters 50
- 7.3.2 Parameter Shortcut 50
- 7.3.3 Parameter List 51
- 7.4 Primary Motor Settings 52
- 7.4.1 Brake 53
- 7.5 Protection 53
- 7.5.1 Current Imbalance 53
- 7.5.2 Undercurrent 53
- 7.5.4 Frequency Trip 54
- 7.6 Inputs 54
- * [00:00 - 30:00 55
- 7.7 Outputs 56
- 7.7.1 Relay A Delays 56
- 7.7.2 Relays B and C 56
- 7.7.4 Motor Temperature Flag 57
- 7.7.5 Analog Output A 57
- 7.8 Start/Stop Timers 57
- 7.9 Auto-Reset 58
- 7.9.1 Auto-Reset Delay 58
- 7.10 Secondary Motor Set 58
- 7.11 Display 60
- 7.11.2 Performance Graphs 61
- 7.12 Restricted Parameters 61
- * [100 - 2000 62
- 8.1 Set Date and Time 63
- 8.2 Load/Save Settings 63
- 8.3 Reset Thermal Model 63
- 8.4 Protection Simulation 63
- 8.5 Output Signal Simulation 64
- 8.6 Digital I/O State 64
- 8.7 Temp Sensors State 64
- 8.8 Alarm Log 64
- 8.8.1 Trip Log 64
- 8.8.2 Event Log 65
- 8.8.3 Counters 65
- 9.2 General Faults 69
- Symptom Probable Cause 70
- 10.1 Accessories 72
- 10.1.1 Communication Modules 72
- 10.1.2 PC Software 73
- 10.1.3 Finger Guard Kit 73
- *MG17K302* 77
Related products and manuals for Circular saws Delta 28-299A
Circular saws Delta 36-5000 Instruction Manual
(100 pages)
(100 pages)
Circular saws Delta 20-140 User Manual
(8 pages)
Circular saws Delta 36-648 User Manual
(12 pages)
(12 pages)
Circular saws Delta 36-600 User Manual
(15 pages)
(15 pages)
Circular saws Delta MS210 User Manual
(35 pages)
(35 pages)
Circular saws Delta 36-075 User Manual
(28 pages)
(28 pages)
Circular saws Delta 20-140 User Manual
(5 pages)
(5 pages)
© 2020, manymanuals.com. All rights reserved. | 2.223 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals