Delta 50-850 Instruction Manual download pdf (Page 6)

6 - English

FOREWORD

The 50-850 Dust Collector will connect to woodworking machines that accept a 4" (101.6 mm) diameter hose. The

50-850 comes with a five micron filter bag, one six mil plastic collection bag and a 4" x 5' (101.6 mm x 1524 mm)

collection hose.

FUNCTIONAL DESCRIPTION

EXTENSION CORDS

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord

which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using an

extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop

in line voltage, resulting in loss of power and overheating. Fig. D-1 or D-2, shows the correct gauge to use depending on

the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

NOTICE: The illustration on the manual cover shows the current production model. All other illustrations contained in the

manual are representative only and may not depict the actual labeling or accessories included. These are intended to

illustrate technique only.

3. 240 VOLT SINGLE PHASE OPERATION

The motor supplied with your machine is a dual

voltage, 120/240 volt motor. It is shipped ready-

to-run for 120 volt operation. However, it can be

converted for 240 volt operation.

A qualified electrician should do the conversion, or

the machine can be taken to an Authorized Delta

Service Center. When completed, the machine must

conform to the National Electric Code and all local

codes and ordinances.

The machine is typically converted by re-wiring the

motor for 240 volts, installing a 240 volt plug on the

power supply cord and replacing the switch with one

that is rated for 240 volt operation.

Be sure the 240 volt plug is only used in an outlet

having the same configuration as the plug illustrated

in Fig. C. No adapter should be used with the 240

volt plug.

Fig. C

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

GROUNDING BLADE

IS LONGEST OF THE 3 BLADES

Fig. D-1

Fig. D-2

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere Total Length Gauge of

Rating Volts of Cord in Feet Extension Cord

0-6 120

up to

25 18 AWG

0-6 120 25-50 16 AWG

0-6 120 50-100 16 AWG

0-6 120 100-150 14 AWG

6-10 120

up to

25 18 AWG

6-10 120 25-50 16 AWG

6-10 120 50-100 14 AWG

6-10 120 100-150 12 AWG

10-12 120

up to

25 16 AWG

10-12 120 25-50 16 AWG

10-12 120 50-100 14 AWG

10-12 120 100-150 12 AWG

12-16 120

up to

25 14 AWG

12-16 120 25-50 12 AWG

12-16 120

GREATER THAN 50 FEET NOT RECOMMENDED

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere Total Length Gauge of

Rating Volts of Cord in Feet Extension Cord

0-6 240

up to

50 18 AWG

0-6 240 50-100 16 AWG

0-6 240 100-200 16 AWG

0-6 240 200-300 14 AWG

6-10 240

up to

50 18 AWG

6-10 240 50-100 16 AWG

6-10 240 100-200 14 AWG

6-10 240 200-300 12 AWG

10-12 240

up to

50 16 AWG

10-12 240 50-100 16 AWG

10-12 240 100-200 14 AWG

10-12 240 200-300 12 AWG

12-16 240

up to

50 14 AWG

12-16 240 50-100 12 AWG

12-16 240

GREATER THAN 100 FEET NOT RECOMMENDED

In all cases, make certain that

the receptacle in question is properly grounded.

If you are not sure, have a qualified electrician

check the receptacle.

1 2 3 4 5 6 7 8 9 10 11 ... 43 44

Comments to this Manuals

No comments

Delta 50-850 Instruction Manual Page 6

Comments to this Manuals

Related products and manuals for Dust covers Delta 50-850