Delta TS300 Instruction Manual download pdf (Page 12)

1. Align the three slotted holes in the front right guide rail (A) Fig. 14 with the two holes (B) in the saw table and the slotted

hole (C) in the extension wing.

2. Insert an M6 x 1 x 20mm carriage head screw (D) Fig. 14 through the three holes in the front right guide rail and the

saw table.

3. Place an M6.4 flat washer (E) and a 6.1 lockwasher (F) on the carriage head screw (D) Thread and M6 x 1 hex nut (G)

on the carriage head screw (D) and HAND TIGHTEN ONLY.

4. Insert the longer end of the front guide rail extension connector (H) into the end of the guide rail.

GUIDE RAILS

5. Attach the front left guide rail (J) Fig. 16 to the

extension connector (H).

6. Align the two slotted holes in the guide rail extension (J)

Fig. 16 with the holes in the table (K) and the extension

wing (L).

7. Insert an M6 x 1 x 20mm carriage head screw (D) Fig.

16 through the two holes in the front left guide rail and

the saw table.

8. Place a M6.4 flat washer (E) and a 6.1 lockwasher (F)

on the carriage head screw (D). Thread a M6x1 hex nut

(G) onto the carriage head screw (D) and HAND

TIGHTEN ONLY.

9. Align the holes in the longer section of rear guide rail (P) Fig. 17 with the holes (A, B, and C) in the saw table. Place an

M8.1 lockwasher and an M8.4 flat washer on a M8 x 1.25 x 16mm hex head screw. Insert the screw through the hole (A)

Fig. 17 in the rear guide rail. Place an M8.4 flat washer and an M8.1 lockwasher on the hex head screw. Thread an

M8x1.25 hex nut on the hex head screw. HAND TIGHTEN ONLY.

10. Place an M8.1 lockwasher and an M8.4 flat washer on an M8 x 1.25 x 16mm hex head screw. Insert the screw through

the holes (B) and (C) Fig. 17 in the rear guide rail. Thread it into the tapped hole in the saw table. HAND TIGHTEN ONLY.

11. Align the holes in the shorter section of rear guide rail (R) Fig. 17 with the holes (D) and (E) in the in the saw table. Place

an M8.1 lockwasher and an M8.4 flat washer on a M8 x 1.25 x 16mm hex head screw. Insert the screw through the hole

(E) Fig. 17 in the rear guide rail. Place an M8.4 flat washer and an M8.1 lockwasher on the hex head screw. Thread an

M8 x 1.25 hex nut on the hex head screw. HAND TIGHTEN ONLY.

12. Place an M8.1 lockwasher and an M8.4 flat washer on a M8 x 1.25 x 16mm hex head screw. Insert the screw through

the hole (D) Fig. 17 in the rear guide rail. Thread it into the tapped hole in the saw table. HAND TIGHTEN ONLY.

13. Use a square (X) Fig. 18 or a ruler to adjust the rail so that it is 7/16" from the top of the table along the entire length.

14. Tighten all mounting hardware.

Fig. 14

Fig. 15

Fig. 16

Fig. 17

Fig. 18

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 26 27

No comments

Delta TS300 Instruction Manual Page 12