Delta BS150LS Instruction Manual download pdf (Page 6)

Fig. D

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere Total Length Gauge of

Rating Volts of Cord in Feet Extension Cord

0-6 120

up to

25 18 AWG

0-6 120 25-50 16 AWG

0-6 120 50-100 16 AWG

0-6 120 100-150 14 AWG

6-10 120

up to

25 18 AWG

6-10 120 25-50 16 AWG

6-10 120 50-100 14 AWG

6-10 120 100-150 12 AWG

10-12 120

up to

25 16 AWG

10-12 120 25-50 16 AWG

10-12 120 50-100 14 AWG

10-12 120 100-150 12 AWG

12-16 120

up to

25 14 AWG

12-16 120 25-50 12 AWG

12-16 120 GREATER THAN 50 FEET NOT RECOMMENDED

Use proper extension cords. Make sure

your extension cord is in good condition and is a 3-

wire extension cord which has a 3-prong grounding

type plug and matching receptacle which will accept

the machine’s plug. When using an extension cord,

be sure to use one heavy enough to carry the current

of the machine. An undersized cord will cause a drop

in line voltage, resulting in loss of power and over-

heating. Fig. D-1 or D-2, shows the correct gauge to

use depending on the cord length. If in doubt, use

the next heavier gauge. The smaller the gauge num-

ber, the heavier the cord.

Fig. A

Fig. B

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

GROUNDING BLADE

IS LONGEST OF THE 3 BLADES

GROUNDED OUTLET BOX

GROUNDING MEANS

ADAPTER

GROUNDING INSTRUCTIONS

This machine must be grounded while in use to protect the operator from electric shock.

1. All grounded, cord-connected machines:

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to

reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding conduc-tor can result in risk of electric shock. The conductor

with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding

conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-

grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely

understood, or if in doubt as to whether the machine is properly grounded.

Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that

accept the machine’s plug, as shown in Fig. A.

Repair or replace damaged or worn cord immediately.

2. Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less

than 150 volts:

If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. A, the

machine will have a grounding plug that looks like the plug illustrated in Fig. A. A temporary adapter, which looks

like the adapter illustrated in Fig. B, may be used to connect this plug to a matching 2-conductor receptacle as

shown in Fig. B if a properly grounded outlet is not available. The temporary adapter should be used only until

a properly grounded outlet can be installed by a qualified electrician. The green-colored rigid ear, lug, and the

like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet

box. Whenever the adapter is used, it must be held in place with a metal screw.

NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.

In all cases, make certain that the receptacle in question is properly grounded. If you are not sure,

have a qualified electrician check the receptacle.

EXTENSION CORDS

1 2 3 4 5 6 7 8 9 10 11 ... 71 72

Comments to this Manuals

No comments

Delta BS150LS Instruction Manual Page 6

Comments to this Manuals

Related products and manuals for Circular saws Delta BS150LS