Delta SA180 Operations Instructions download pdf (Page 5)

1. DO NOT OPERATE THIS MACHINE until it is

completely assembled and installed according to

the instructions. A machine incorrectly assembled

can cause serious injury.

2. OBTAIN ADVICE from your supervisor, instructor,

or another qualified person if you are not thoroughly

familiar with the operation of this machine.

Knowledge is safety.

3. FOLLOW ALL WIRING CODES and recommended

electrical connections to prevent shock or

electrocution.

4. NEVER TURN THE MACHINE "ON" before

clearing the table/work area of all objects (tools,

scraps of wood, etc.). Flying debris is dangerous.

5. NEVER TURN THE MACHINE "ON" with the work-

piece contacting the abrasive surface. Kickback

can occur.

6. SECURE THE MACHINE to a supporting surface.

Vibration can cause the machine to slide, walk, or

tip over.

7. COVER THE POWER TAKE-OFF SHAFT when not

using accessories. Unguarded rotating shafts can

create an entanglement hazard which can result in

injury.

8. USE A DUST COLLECTION SYSTEM. Some types

of wood are known to cause disease or other health

problems.

9. CLEAN THE MACHINE and dust collector thoroughly

when processing different types of workpieces

(wood, steel, or aluminum). Combining wood and

metal dust can create an explosion or fire hazard.

DO NOT SAND OR POLISH MAGNESIUM. Fire

will result.

10. PREVENT THE WORKPIECE from contacting the

sanding belt before starting the tool. Loss of control

of the workpiece is dangerous.

11. AVOID AWKWARD OPERATIONS AND HAND

POSITIONS. A sudden slip could cause a hand to

move into the abrasive disc or belt.

12. MAINTAIN A MAXIMUM CLEARANCE OF 1/16"

between the table and the abrasive disc. The

workpiece could be drawn into the space between

the abrasive disc and the table.

13. SUPPORT THE WORKPIECE firmly with a miter

gauge, backstop, or work table when sanding with

a belt. Hold the workpiece firmly. Loss of control of

the workpiece can result in injury.

14. AVOID KICKBACK by sanding in accordance

with the directional arrows. Feed the workpiece

against the downward rotation side of the disc or

the forward rotation of the belt. Loss of control of

the workpiece can result in injury.

15. DO NOT SAND very small or very thin workpieces

that cannot be safely controlled. Loss of control of

the workpiece can result in injury.

16. PROPERLY SUPPORT LONG OR WIDE

WORKPIECES.

Loss of control of the workpiece is

dangerous.

17. NEVER PERFORM LAYOUT, ASSEMBLY, OR SET-UP

WORK on the table/work area when the machine is

running. A sudden slip could cause a hand to move

into the abrasive surface. Severe injury can result.

18. TURN THE MACHINE "OFF", disconnect the

machine from the power source, and clean the

table/work area before leaving the machine. LOCK

THE SWITCH IN THE "OFF" POSITION to prevent

unauthorized use. Someone else might accidentally

start the machine and cause injury to themselves.

19. ADDITIONAL INFORMATION regarding the safe

and proper operation of power tools (i.e. a safety

video) is available from the Power Tool Institute, 1300

Sumner Avenue, Cleveland, OH 44115-2851(www.

powertoolinstitute.com). Information is also available

from the National Safety Council, 1121 Spring Lake

Drive, Itasca, IL 60143-3201. Please refer to the

American National Standards Institute ANSI 01.1

Safety Requirements for Woodworking Machines

and the U.S. Department of Labor OSHA 1910.213

Regulations.

Failure to follow these rules may result in serious personal injury.

ADDITIONAL SPECIFIC SAFETY RULES

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

1 2 3 4 5 6 7 8 9 10 ... 59 60

Comments to this Manuals

No comments

Delta SA180 Operations Instructions Page 5

Comments to this Manuals

Related products and manuals for Power sanders Delta SA180