Delta 11-985 Instruction Manual download pdf (Page 3)

23. NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Don't leave tool until it comes to a

complete stop.

24. DRUGS, ALCOHOL, MEDICATION. Do not operate

tool while under the influence of drugs, alcohol or any

medication.

25. MAKE SURE TOOL IS DISCONNECTED FROM

POWER SUPPLY while motor is being mounted,

connected or reconnected.

26. THE DUST GENERATED by certain woods and

wood products can be injurious to your health. Always

operate machinery in well ventilated areas and provide

for proper dust removal. Use wood dust collection

systems whenever possible.

1. DO NOT operate your drill press until it is

completely assembled and installed according to the

instructions.

2. IF YOU ARE NOT thoroughly familiar with the

operation of drill presses, obtain advice from your

supervisor, instructor or other qualified person.

3. YOUR DRILL PRESS MUST be securely fastened

to a stand or workbench. If there is any tendency for the

stand or workbench to move during operation, the stand

or workbench MUST be fastened to the floor.

4. NEVER turn the drill press "on" before clearing the

table of all objects (tools, scrap pieces, etc.).

5. NEVER start the drill press with the drill bit or cutting

tool in contact with the workpiece.

6. USE ONLY drill bits, cutters, sanding drums and

other accessories with 1/2 shank or less.

7. ALWAYS keep hands and fingers away from the drill

bit or cutting tool.

8. DO NOT ATTEMPT to drill material that does not

have a flat surface, unless a suitable support is used.

9. AVOID awkward hand positions where a sudden slip

could cause a hand to move into the drill bit or cutting

tool.

10. TO PREVENT ROTATION OF THE WORKPIECE,

ALWAYS clamp work securely to table if it is too short to

contact the column (see "OPERATION" section of this

manual) or when using hole saw or cutting tools larger

than

1/2 in diameter.

11. WHENEVER POSSIBLE use clamps or vise to keep

workpiece from rotating with the drill bit or cutting tool.

12. USE recommended speed for drill, accessory or

workpiece material.

13. MAKE CERTAIN all lock handles are tightened

SAVE THESE INSTRUCTIONS.

27. WARNING: SOME DUST CREATED BY POWER

SANDING, SAWING, GRINDING, DRILLING, AND

OTHER CONSTRUCTION ACTIVITIES contains

chemicals known to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals

are:

•

lead from lead-based paints,

•

crystalline silica from bricks and cement and

other·masonry products, and

•

arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such as

those dust masks that are specially designed to filter out

microscopic particles.

ADDITIONAL SAFETY RULES

FOR DRILL PRESSES

before starting the machine.

14. NEVER perform layout, assembly or set-up work on

the table while the drill is operating.

15. BE SURE drill bit or cutting tool is not damaged and

is properly locked in the chuck before operating.

16. MAKE SURE chuck key is removed from chuck

before starting drill press. ONLY use chuck key provided

with your drill press. It is equipped with a self-ejecting

pin which eliminates the hazard of the key being left in

the chuck.

17. ADJUST the table or depth stop to avoid drilling into

the table.

18. ALWAYS stop the drill press before removing scrap

pieces from the table.

19. WHEN drilling large workpieces, MAKE SURE the

material is supported at table height.

20. SHUT OFF the power, remove the drill bit or cutting

tool, and clean the table and work area before leaving

the machine.

21. DON'T wear gloves, necktie, or loose clothing when

operating the drill press.

22. SHOULD any part of your drill press be missing,

damaged or fail in anyway, or any electrical component

fail to perform properly, shut off switch and remove plug

from power supply outlet. Replace missing, damaged or

failed parts before resuming operation.

23. ADDITIONAL INFORMATION regarding the safe

and proper operation of this product is available from

the National Safety Council, 1121 Spring Lake Drive,

Itasca, Illinois 60143-3201, in the Accident Prevention

Manual for Industrial Operations and also in the Safety

Data Sheets provided by the NSC. Please also refer to

the American National Standards Institute ANSI 01.1

Safety Require-ments for Woodworking Machinery and

the U.S. Department of Labor OSHA 1910.212 and

1910.213 Regulations.

1 2 3 4 5 6 7 8 ... 15 16

Comments to this Manuals

No comments

Delta 11-985 Instruction Manual Page 3

Comments to this Manuals

Related products and manuals for Power tools Delta 11-985