Delta 1.07 VFD-D D User Manual Page 86
- Page / 141
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 4 Parameter Settings|DD Series
4-62
07 Control Parameters This parameter can be set during operation.
ASR (Auto Speed Regulation) Control (P) of Zero Speed
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 1.5
Settings 0.0~500.0%
ASR (Auto Speed Regulation) Control (I) of Zero Speed
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 0.050
Settings 0.000~10.000sec
ASR (Auto Speed Regulation) Control (P) 1
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 1.5
Settings 0.0~500.0%
ASR (Auto Speed Regulation) Control (I) 1
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 0.050
Settings 0.000~10.000sec
ASR (Auto Speed Regulation) Control (P) 2
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 3.0
Settings 0.0~500.0%
ASR (Auto Speed Regulation) Control (I) 2
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 0.100
Settings 0.000~10.000sec
ASR 1/ASR2 Switch Frequency
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 2.00
Settings 0.00~120.00Hz (0: disable)
ASR P determines Proportional control and associated gain (P). ASR I determines integral control and
associated gain (I).
When integral time is set to 0, it is disabled. Pr.07-06 defines the switch frequency for ASR1 (Pr.07-02,
07-03) and ASR2 (Pr.07-04, Pr.07-05).
07.06
07.02
07.03
07.04
07.05
Hz
PI
07.00
07.01
0H
z
07.08
07.09
ASR Primary Low Pass Filter Gain
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 0.008
Settings 0.000~0.350sec
This parameter defines the filter time of the ASR command.
- ''( 1
- 1
- Preface 2
- Table of Content 5
- Chapter 1 Introduction 7
- 1-1 Receiving and Inspection 8
- T02DD21A0 9
- Minimum Mounting Clearances 10
- CAUTION! 11
- Dimensions for Motor 12
- ECMD-B9160GMS 13
- Chapter 2 Wiring 14
- 2-1 Wiring Diagram 15
- Used with external power 16
- Not allowed 17
- 2-2 Main Circuit Terminal 18
- Chapter 2 Wiring 19
- 2-3 Control Circuit Terminal 20
- 3-1 Operation Method 23
- 3-2 Keypad Descriptions 24
- Chapter 4 Parameter Settings 25
- Settings 28
- Parameter Reset 48
- Start-up Display Selection 48
- Software version 49
- Password Input 49
- Password Set 49
- Control Method 50
- Door Control Mode 51
- Output Direction 52
- Demo Mode 53
- Frequency Testing Command 53
- Motor Auto Tuning (PM) 55
- Motor Auto Tuning (IM) 57
- Output Voltage 3 61
- Output Frequency 4 61
- Output Voltage 4 61
- OD:("OPEN":STOP) 62
- CD:(" OPEN": STOP) 62
- Multi-function Output (MO3) 65
- Digital Output Direction 66
- Position Detection Signal 1 66
- Encoder (PG) Signal Type 68
- Encoder pulse 68
- Encoder Input Type Setting 68
- Door Width Pulses (Unit:1) 70
- 04.19=S1 73
- 04.20=S2 73
- Freqeunc 73
- VFPG SVC FOCPG 74
- 05.19=S1 77
- 05.20=S2 77
- Door Re-open Detection Time 79
- Quadrant I 80
- Quadrant II 80
- Quadrant III 80
- Quadrant IV 80
- Low Voltage Level 81
- Position Control Mode 82
- VFPG SVC FOCPG FOCPM 84
- Auto Restart After Fault 85
- Gain for Speed Feed Forward 88
- VFPG SVC FOCPG FOCPM 89
- Communication Address 90
- Transmission Speed 90
- Transmission Fault Treatment 90
- Time-out Detection 90
- Communication Protocol 90
- Code Description: 91
- Status monitor 97
- Read only 97
- Example: 98
- Response Delay Time 99
- Multi-function Output RY1 103
- Multi-function Output RY2 103
- View User-defined Parameters 103
- 2 1 1B 104
- 111x16 + x16 =16+11 = 104
- Enter 2127 104
- Chapter 5 Troubleshooting 106
- 5-1 Over Current (oc) 107
- 5-2 Ground Fault (GFF) 108
- 5-3 Over Voltage (ov) 109
- 5-4 Low Voltage (Lv) 110
- 5-5 Over Heat (oH1) 111
- 5-6 Overload (oL) 112
- 5-8 Phase Loss (PHL) 114
- 5-9 Motor is not Running 115
- 5-12 Motor Run Error 118
- 5.14 Environmental Condition 120
- High Harmonic at Power Side 121
- Motor Temperature Rises 121
- 6.1.1 Reset 127
- Voltage 128
- Keypad 128
- Mechanical parts 128
- Main circuit 129
- Resistor of main circuit 130
- Control Characteristics 132
- Motor Model 134
- Appendix B 135
- B-1 Capacity Formulas 136
- Symbol explanation 137
- B-2 General Precautions 138
- Drives Selection 138
- Parameter Settings 138
- Standard motor 139
- Special motors: 140
- Power Transmission Mechanism 140
- Motor torque 141
© 2020, manymanuals.com. All rights reserved. | 2.673 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals