Delta MM300 Instruction Manual Page 106
- Page / 167
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
CHAPTER 6: SETPOINTS CONFIGURATION SETPOINTS
MM300 MOTOR MANAGEMENT SYSTEM – INSTRUCTION MANUAL 6–19
NOTE
NOTE:
When changing the IP address, power to the relay must be cycled in order for the new IP
address to become active.
Ethernet Subnet Mask
Range: standard IP address format
Default: 255.255.252.0
This setpoint specifies the subnet IP mask provided by the network administrator.
Ethernet Gateway Address
Range: standard IP address format
Default: 0.0.0.0
This setpoint specifies the gateway IP address provided by the network administrator.
NTP Address
This setpoint is set to the IP address of the external clock source.
Profibus Address
Range: 1 to 125
Default: 125
Specifies the Profibus Slave address for this node.
Profibus Baud Rate
Range: 9600, 19200, 31250, 45450, 93750, 187500, 500K, 1.5M, Autodetect
Default: Autodetect*
Specifies the speed of communication for the Profibus inteface.
* Profibus communications will operate only in 1.5Mbps or auto-detect with the
presentimplementation. Auto-detect includes all listed baud rates.
Comms OK Evaluation
Range: Serial, Serial + Ethernet, Serial + Fieldbus, Ethernet, Fieldbus, Ethernet + Fieldbus,
All
Default: Serial
Specifies the operands for the Comms OK flag.
Comm Failure Trip
Range: Off, 5 to 25 step 5s
Default: Off
Specifies the time without comms before a trip will be generated.
Comm Failure Alarm
Range: Off, 5 to 25 step 5s
Default: Off
Specifies the time without comms before an alarm will be generated.
NOTE
NOTE:
Timing delay commences after failure is detected.
Change Mode on Comm Alarm
Range: Disabled, Enabled
Default: Disabled
If enabled, forces control mode to manual if comms are lost.
- Instruction manual 1
- Motor Management System 1
- Table of Contents 3
- Chapter 1: Introduction 7
- Figure 2: Single line diagram 9
- 1.1.3 MM300 order codes 10
- 1.2 Specifications 12
- 1.2.4 Control specifications 14
- 1.2.5 Inputs specifications 14
- 1.2.6 Outputs specifications 16
- CERTIFICATION 17
- TYPE TESTS 17
- DIMENSIONS 17
- OPERATING ENVIRONMENT 18
- Chapter 2: Installation 20
- 2.1.2 Product identification 21
- 2.1.3 Mounting 21
- CAUTION: 22
- Figure 5: DIN rail mounting 23
- 853727A1.CDR 24
- 853733A1.CDR 25
- 853734A1.CDR 25
- 2.2.1 Power supply module 28
- 2.2.2 CPU module 28
- MM300 IED 31
- 853745A1.CDR 31
- 2.2.3 Protection modules 32
- Core Balance (Zero Sequence) 33
- 2.2.3.2 Two CT configuration 34
- FUSES - 100 ma typical 35
- 2.2.4 Input/output modules 36
- Consumer & Industrial 39
- Multilin 39
- 2.3 Starter types 40
- Low Voltage 41
- 2.3.3 Two-speed starter 42
- 2.3.6 Soft starter type 48
- 3.1.1.1 Graphical display 51
- 3.1.1.2 Keypad 52
- 3.1.1.3 Control keys 54
- 3.1.1.4 LED indicators 54
- Main menu 55
- Level 1 Level 2 Level 3 55
- 3.1.2.1 Home display page 56
- 3.1.2.2 Default display 56
- 3.1.2.3 Actual values pages 56
- 3.1.2.4 Status pages 57
- 3.1.2.5 Setpoints pages 59
- 3.1.2.6 Diagnostics pages 60
- 3.1.2.7 Control page 61
- 3.1.2.8 Popup windows 61
- 3.1.3.2 Numeric setpoints 63
- 3.1.3.5 Security access 65
- 3.2 Basic control panel 66
- Chapter 4: Software operation 68
- 4.1.1 Software requirements 69
- USB port: 71
- 4.2 Power analysis 76
- 4.2.2 Data logger 79
- Chapter 5: Actual values 82
- 5.2 Metering 83
- 5.2.3 Power metering 84
- 5.2.4 Sensor metering 84
- 5.3 Status 85
- 5.3.3 System Page 86
- 5.3.4 Flex Page 86
- Chapter 6: Setpoints 88
- 6.2 Configuration setpoints 90
- Full Voltage Non-reversing 92
- Full Voltage Reversing 92
- Two Speed Starter 92
- Wye-Delta Starter 92
- 853717A1.CDR 93
- 6.2.1.4 Two-speed starter 94
- 853719A1.CDR 95
- 6.2.1.6 Inverter starter 96
- 853721A1.CDR 97
- 6.2.1.7 Soft starter 98
- 6.2.3 Inputs 101
- 6.2.4 Outputs 102
- 6.2.6 System 107
- 6.2.7 Events 109
- 6.2.8 Waveforms 110
- 6.2.9 Datalog 110
- 6.2.10 Counters 111
- 6.3 Protection elements 113
- 6.3.1.1 Unbalance biasing 113
- 6.3.1.2 Hot/cold biasing 114
- 6.3.1.3 RTD biasing 115
- 6.3.1.4 Overload curve 116
- TIME IN SECONDS 117
- 6.3.1.5 Cooling rate 118
- Time (minutes) 119
- RTD Bias – 121
- Maximum T 121
- RTD Bias – Center T 121
- 6.3.2.1 Mechanical jam 122
- 6.3.3 Electrical protection 125
- Ground CT setpoint 126
- 6.3.3.3 Load increase alarm 127
- 6.3.3.4 Phase undervoltage 127
- 6.3.3.6 Phase overvoltage 128
- 6.3.3.7 Phase reversal 129
- 6.3.3.8 Fuse failure 129
- 6.3.4.1 RTD protection 130
- 6.4 Control elements 133
- 6.4.1.1 Auto/manual control 133
- Start Ctrl 135
- External Stop Action 136
- 6.4.2 Starting duty inhibits 137
- 6.4.3 Process interlocks 139
- 853703A1.CDR 140
- IL Function A setpoint 141
- 6.5 System security 144
- MM300 Motor Management System 146
- Chapter 7: Diagnostics 146
- EVENTS CHAPTER 7: DIAGNOSTICS 147
- 7.2 Digital counters 148
- 7.3 Phasors 150
- 7.4 Product information 151
- 7.5 Learned data 152
- 7.6 Waveform 153
- 7.7 Datalog 154
- Chapter 8: FlexLogic™ 156
- Chapter 9: Communications 162
- Appendix 164
- APPENDIX 165
- Section Number CHANGES 165
Related products and manuals for Power tools Delta MM300
Power tools Delta 36-040 Instruction Manual
(17 pages)
(17 pages)
Power tools Delta 14-651 Instruction Manual
(40 pages)
(40 pages)
Power tools Delta 36-850 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 14-070 User Manual
(8 pages)
(8 pages)
Power tools Delta 23-725 Instruction Manual
(44 pages)
(44 pages)
Power tools Delta GR050 Specifications
(64 pages)
(64 pages)
Power tools Delta 17-950L Instruction Manual
(64 pages)
(64 pages)
Power tools Delta 32-325 Instruction Manual
(20 pages)
(20 pages)
Power tools Delta TP305 Instruction Manual
(48 pages)
(48 pages)
Power tools Delta 36-205 User Manual
(4 pages)
(4 pages)
Power tools Delta 23-700 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 23-725 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta ts200ls Instruction Manual
(27 pages)
(27 pages)
Power tools Delta 23-710 Instruction Manual
(64 pages)
(64 pages)
Power tools Delta DP350 Instruction Manual
(17 pages)
(17 pages)
Power tools Delta BS150LS Instruction Manual
(25 pages)
(25 pages)
Power tools Delta 50-760 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 23-710 Instruction Manual
(24 pages)
(24 pages)
Power tools Delta 36-979 Instruction Manual
(17 pages)
(17 pages)
© 2020, manymanuals.com. All rights reserved. | 0.250 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals