Delta MM300 Instruction Manual Page 160
- Page / 167
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
CHAPTER 8: FLEXLOGIC™ FLEXLOGIC™ OVERVIEW
MM300 MOTOR MANAGEMENT SYSTEM – INSTRUCTION MANUAL 8–5
Protection operands: overvoltage
Overvoltage Alarm ................ Asserted when an overvoltage alarm condition exists.
Overvoltage Trip..................... Asserted when an overvoltage trip condition exists.
Protection operands: phase reversal
Phase Reversal Alarm .......... Asserted when a phase reversal alarm condition exists.
Phase Reversal Inhibit.......... Asserted when a phase reversal condition inhibits starting.
Phase Reversal Trip............... Asserted when a phase reversal trip condition exists.
Protection operands: RTD protection
RTD #1 Alarm ........................... Asserted when an RTD #1 alarm condition exists.
RTD #1 Trip................................ Asserted when an RTD #1 trip condition exists.
RTD #2 to RTD #6 ................... The same set of operands shown above are available for RTDs
2 through 6.
RTD Open/Short Alarm ........ Asserted when any configured RTD channel is found to be an
open circuit when any configured RTD channel is found to be
shorted or showing less than –50°C..
Protection operands: starting duty inhibits
Thermal Inhibit ........................ Asserted when the motor is too hot to be started.
Time Between Inhibit ........... Asserted when the minimum time between starts has not
expired since the last motor start.
Protection operands: thermal model
Thermal Level Alarm............. Asserted when the thermal capacity used alarm condition
exists.
Thermal O/L Trip..................... Asserted when the thermal model has operated and the motor
has cooled, but the trip has not yet been reset.
Protection operands: thermistor protection
Thermistor Alarm ................... Asserted when a thermistor alarm condition exists.
Thermistor Trip........................ Asserted when a thermistor trip condition exists.
Protection operands: undercurrent
Undercurrent Alarm.............. Asserted when an undercurrent alarm condition exists.
Undercurrent Trip................... Asserted when an undercurrent trip condition exists.
Protection operands: underpower
Underpower Alarm................ Asserted when an underpower alarm condition exists.
Underpower Trip..................... Asserted when an underpower trip condition exists.
Protection operands: undervoltage
Undervoltage Alarm ............. Asserted when an undervoltage alarm condition exists.
Undervoltage Trip.................. Asserted when an undervoltage trip condition exists.
System trouble operands
Open Control Circuit ............. Asserted when an open control circuit is detected.
Self-Test Alarm ........................ Asserted when the self-test has failed and is set for alarm.
Self-Test Trip............................. Asserted when the self-test has failed and is set for trip.
Welded Contactor Alarm.... Asserted when a welded contactor is detected.
Communication trouble operands
Comm Fail Trip ........................ Asserted when a loss of communication is detected.
Comm Fail Alarm.................... Asserted when a loss of communication is detected.
Maintenance
Drive Greasing Alarm ........... Asserted when the running hours exceed the alarm level.
- Instruction manual 1
- Motor Management System 1
- Table of Contents 3
- Chapter 1: Introduction 7
- Figure 2: Single line diagram 9
- 1.1.3 MM300 order codes 10
- 1.2 Specifications 12
- 1.2.4 Control specifications 14
- 1.2.5 Inputs specifications 14
- 1.2.6 Outputs specifications 16
- CERTIFICATION 17
- TYPE TESTS 17
- DIMENSIONS 17
- OPERATING ENVIRONMENT 18
- Chapter 2: Installation 20
- 2.1.2 Product identification 21
- 2.1.3 Mounting 21
- CAUTION: 22
- Figure 5: DIN rail mounting 23
- 853727A1.CDR 24
- 853733A1.CDR 25
- 853734A1.CDR 25
- 2.2.1 Power supply module 28
- 2.2.2 CPU module 28
- MM300 IED 31
- 853745A1.CDR 31
- 2.2.3 Protection modules 32
- Core Balance (Zero Sequence) 33
- 2.2.3.2 Two CT configuration 34
- FUSES - 100 ma typical 35
- 2.2.4 Input/output modules 36
- Consumer & Industrial 39
- Multilin 39
- 2.3 Starter types 40
- Low Voltage 41
- 2.3.3 Two-speed starter 42
- 2.3.6 Soft starter type 48
- 3.1.1.1 Graphical display 51
- 3.1.1.2 Keypad 52
- 3.1.1.3 Control keys 54
- 3.1.1.4 LED indicators 54
- Main menu 55
- Level 1 Level 2 Level 3 55
- 3.1.2.1 Home display page 56
- 3.1.2.2 Default display 56
- 3.1.2.3 Actual values pages 56
- 3.1.2.4 Status pages 57
- 3.1.2.5 Setpoints pages 59
- 3.1.2.6 Diagnostics pages 60
- 3.1.2.7 Control page 61
- 3.1.2.8 Popup windows 61
- 3.1.3.2 Numeric setpoints 63
- 3.1.3.5 Security access 65
- 3.2 Basic control panel 66
- Chapter 4: Software operation 68
- 4.1.1 Software requirements 69
- USB port: 71
- 4.2 Power analysis 76
- 4.2.2 Data logger 79
- Chapter 5: Actual values 82
- 5.2 Metering 83
- 5.2.3 Power metering 84
- 5.2.4 Sensor metering 84
- 5.3 Status 85
- 5.3.3 System Page 86
- 5.3.4 Flex Page 86
- Chapter 6: Setpoints 88
- 6.2 Configuration setpoints 90
- Full Voltage Non-reversing 92
- Full Voltage Reversing 92
- Two Speed Starter 92
- Wye-Delta Starter 92
- 853717A1.CDR 93
- 6.2.1.4 Two-speed starter 94
- 853719A1.CDR 95
- 6.2.1.6 Inverter starter 96
- 853721A1.CDR 97
- 6.2.1.7 Soft starter 98
- 6.2.3 Inputs 101
- 6.2.4 Outputs 102
- 6.2.6 System 107
- 6.2.7 Events 109
- 6.2.8 Waveforms 110
- 6.2.9 Datalog 110
- 6.2.10 Counters 111
- 6.3 Protection elements 113
- 6.3.1.1 Unbalance biasing 113
- 6.3.1.2 Hot/cold biasing 114
- 6.3.1.3 RTD biasing 115
- 6.3.1.4 Overload curve 116
- TIME IN SECONDS 117
- 6.3.1.5 Cooling rate 118
- Time (minutes) 119
- RTD Bias – 121
- Maximum T 121
- RTD Bias – Center T 121
- 6.3.2.1 Mechanical jam 122
- 6.3.3 Electrical protection 125
- Ground CT setpoint 126
- 6.3.3.3 Load increase alarm 127
- 6.3.3.4 Phase undervoltage 127
- 6.3.3.6 Phase overvoltage 128
- 6.3.3.7 Phase reversal 129
- 6.3.3.8 Fuse failure 129
- 6.3.4.1 RTD protection 130
- 6.4 Control elements 133
- 6.4.1.1 Auto/manual control 133
- Start Ctrl 135
- External Stop Action 136
- 6.4.2 Starting duty inhibits 137
- 6.4.3 Process interlocks 139
- 853703A1.CDR 140
- IL Function A setpoint 141
- 6.5 System security 144
- MM300 Motor Management System 146
- Chapter 7: Diagnostics 146
- EVENTS CHAPTER 7: DIAGNOSTICS 147
- 7.2 Digital counters 148
- 7.3 Phasors 150
- 7.4 Product information 151
- 7.5 Learned data 152
- 7.6 Waveform 153
- 7.7 Datalog 154
- Chapter 8: FlexLogic™ 156
- Chapter 9: Communications 162
- Appendix 164
- APPENDIX 165
- Section Number CHANGES 165
Related products and manuals for Power tools Delta MM300
Power tools Delta 36-040 Instruction Manual
(17 pages)
(17 pages)
Power tools Delta 14-651 Instruction Manual
(40 pages)
(40 pages)
Power tools Delta 36-850 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 14-070 User Manual
(8 pages)
(8 pages)
Power tools Delta 23-725 Instruction Manual
(44 pages)
(44 pages)
Power tools Delta GR050 Specifications
(64 pages)
(64 pages)
Power tools Delta 17-950L Instruction Manual
(64 pages)
(64 pages)
Power tools Delta 32-325 Instruction Manual
(20 pages)
(20 pages)
Power tools Delta TP305 Instruction Manual
(48 pages)
(48 pages)
Power tools Delta 36-205 User Manual
(4 pages)
(4 pages)
Power tools Delta 23-700 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 23-725 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta ts200ls Instruction Manual
(27 pages)
(27 pages)
Power tools Delta 23-710 Instruction Manual
(64 pages)
(64 pages)
Power tools Delta DP350 Instruction Manual
(17 pages)
(17 pages)
Power tools Delta BS150LS Instruction Manual
(25 pages)
(25 pages)
Power tools Delta 50-760 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 23-710 Instruction Manual
(24 pages)
(24 pages)
Power tools Delta 36-979 Instruction Manual
(17 pages)
(17 pages)
© 2020, manymanuals.com. All rights reserved. | 1.257 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals