Delta N028314 Instruction Manual Page 6
- Page / 88
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
6
POWER CONNECTIONS
A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should
be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have
3-prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the
machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of
the same characteristics as indicated on the machine. All line connections should make good contact. Running on low
voltage will damage the machine.
Do not expose the machine to rain or operate the machine in damp locations.
MOTOR SPECIFICATIONS
Your machine is wired for 120/240 volt, 60 HZ alternating current. Before connecting the machine to the power source,
make sure the switch is in the “OFF” position.
GROUNDING INSTRUCTIONS
This machine must be grounded while in use to protect the operator from electric shock.
I. Never use the fence as a guide or length stop when crosscutting.
J. Never saw a workpiece with loose knots, flaws, nails or other foreign objects.
K. Never rip a workpiece shorter than 10" (254 mm).
L. Never use a dull blade – replace or have resharpened.
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains
chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of
these chemicals are:
• Leadfromlead-basedpaints,
• Crystallinesilicafrombricksandcementandothermasonryproducts,and
• Arsenicandchromiumfromchemically-treatedlumber(CCA).
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
• Avoid prolonged contact with dust frompower sanding, sawing, grinding, drilling,and other construction
activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your
mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.
Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or
other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles
away from face and body. Always operate tool in well-ventilated area and provide for proper dust removal. Use dust
collection system wherever possible.
SAVE THESE INSTRUCTIONS
1. All grounded, cord-connected machines:
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to
reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conduc-tor can result in risk of electric shock. The conductor
with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding
conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-
grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely
understood, or if in doubt as to whether the machine is properly grounded.
Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that
accept the machine’s plug, as shown in Fig. A.
Repair or replace damaged or worn cord immediately.
- Instruction Manual 1
- Manuel d’Utilisation 1
- Manual de Instrucciones 1
- TABLE OF CONTENTS 2
- IMPORTANT SAFETY INSTRUCTIONS 2
- GENERAL SAFETY RULES 3
- SAVE THESE INSTRUCTIONS 4
- TERMINOLOGY 5
- MAKING A PUSH STICK 5
- KICKBACKS 5
- POWER CONNECTIONS 6
- MOTOR SPECIFICATIONS 6
- GROUNDING INSTRUCTIONS 6
- FUNCTIONAL DESCRIPTION 8
- CARTON CONTENTS 9
- ASSEMBLY 10
- INSTALLING THE DRIVE BELT 11
- EXTENSION WINGS 12
- INSTALLING THE SWITCH 12
- ROUTING THE CORD 13
- INSTALLING THROAT PLATE 15
- ATTACHING A SAW BLADE 15
- ADJUSTING THROAT PLATE 16
- OPERATION 17
- ADJUSTING BLADE ALIGNMENT 18
- MITER GAUGE OPERATION 19
- MACHINE USE 20
- CROSS-CUTTING 21
- MAKING CUTS 21
- BEVEL CROSSCUTTING 22
- COMPOUND MITERING 22
- MITERING 22
- TOP VIEW 23
- BEVEL RIPPING 24
- USING A MOULDING CUTTERHEAD 24
- USING AN ACCESSORY DADO HEAD 25
- USING AUXILIARY WOOD FACING 26
- CONSTRUCTING A FEATHERBOARD 26
- PUSH STICK 27
- TROUBLESHOOTING 28
- MAINTENANCE 28
- ACCESSORIES 29
- WARRANTY 29
- CONSERVER CES DIRECTIVES 30
- RÈGLES DE SÉCURITÉ GÉNÉRALES 31
- TERMINOLOGIE 33
- RACCORDEMENTS ÉLECTRIQUES 34
- SPÉCIFICATIONS DU MOTEUR 34
- DESCRIPTION FONCTIONNELLE 36
- CONTENUS DE BOITE 37
- ASSEMBLAGE 38
- RALLONGES 40
- ACHEMINEMENT DU CORDON 41
- INSTALLATION DES PORTE-OUTILS 44
- ASSEMBLAGE DU GUIDE D’ONGLET 44
- FONCTIONNEMENT 45
- UTILISATION DU GUIDE D’ONGLET 47
- UTILISATION DE LA MACHINE 48
- TRONÇONNAGE 49
- COUPES LONGITUDINALES 50
- VUE EN PLAN 51
- SCIAGE SUR LE LONG EN BISEAU 52
- 19 mm (3/4 po) 54
- 114 mm (4-1/2 po) 54
- POUSSOIR 55
- DEPANNAGE 56
- ENTRETIEN 56
- ACCESSOIRIES 57
- GARANTIE 57
- GUARDE ESTAS INSTRUCCIONES 58
- NORMAS GENERALES DE SEGURIDAD 59
- TÉRMINOS 61
- FABRICANDO UNA VARA DE EMPUJE 61
- ESPECIFICACIONES DEL MOTOR 62
- DESCRIPCIÓN FUNCIONAL 64
- CONTENIDO DE CARTON 65
- ENSAMBLAJE 66
- BASES DE EXTENSIÓN 68
- INSTALACIÓN DEL INTERRUPTOR 68
- RECORRIDO DEL CABLE 69
- ACOPLE DE HOJA 71
- AJUSTE DEL INSERTO DE MESA 72
- OPERACIÓN 73
- UTILIZAR LA MAQUINA 76
- CORTE TRANSVERSAL 77
- CÓMO REALIZAR CORTES 77
- CORTE LONGITUDINAL 78
- VISIÓN SUPERIOR 79
- CORTE LONGITUDINAL CON BISEL 80
- 19 mm (3/4") 82
- 114 mm (4-1/2") 82
- CUADRADOS 83
- DE 12,7 MM (1/2”) 83
- SERVICIO 84
- LOCALIZACION DE FALLAS 84
- MANTENIMIENTO 84
- ACCESORIOS 85
- PÓLIZA DE GARANTÍA 85
- GARANTIA 86
Related products and manuals for Power tools Delta N028314
Power tools Delta 50-861 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 17-925 Instruction Manual
(20 pages)
(20 pages)
Power tools Delta 31-390 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 40 Instruction Manual
(14 pages)
(14 pages)
Power tools Delta TP305 Instruction Manual
(17 pages)
(17 pages)
Power tools Delta 40-570 Instruction Manual
(14 pages)
(14 pages)
Power tools Delta 40-650 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 31-120 Instruction Manual
(12 pages)
(12 pages)
Power tools Delta 23-840 Instruction Manual
(12 pages)
(12 pages)
Power tools Delta JT160 Instruction Manual
(21 pages)
(21 pages)
Power tools Delta GR150 Instruction Manual
(15 pages)
(15 pages)
Power tools Delta 50-770 Instruction Manual
(14 pages)
(14 pages)
Power tools Delta 14-651 Instruction Manual
(15 pages)
(15 pages)
(60 pages)
Power tools Delta AP300 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta GR350 Instruction Manual
(12 pages)
(12 pages)
© 2020, manymanuals.com. All rights reserved. | 0.927 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals