Delta 28-299A Operations Instructions Page 27
- Page / 77
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
4.10.6 UL Tested Fuses - Short Circuit Ratings
M
Model Nominal Rating (A) Short Circuit Rating 480V AC (kA) Short Circuit Rating 600V AC (kA) Fuse Ferraz
MCD5-0021B 23 65 10 AJT50 A070URD30XXX0063
MCD5-0037B 43 65 10 AJT50 A070URD30XXX0125
MCD5-0043B 50 65 10 AJT50 A070URD30XXX0125
MCD5-0053B 53 65 10 AJT60 A070URD30XXX0125
MCD5-0068B 76 65 10 AJT80 A070URD30XXX0200
MCD5-0084B 97 65 10 AJT100 A070URD30XXX0200
MCD5-0089B 100 65 10 AJT100 A070URD30XXX0200
MCD5-0105B 105 65 10 AJT125 A070URD30XXX0315
MCD5-0131B 145 65 18 AJT150 A070URD30XXX0315
MCD5-0141B 170 65 18 AJT175 A070URD30XXX0315
MCD5-0195B 200 65 18 AJT200 A070URD30XXX0450
MCD5-0215B 220 65 18 AJT250 A070URD30XXX0450
MCD5-0245C 255 85 85 AJT300 A070URD30XXX0450
MCD5-0360C 360 85 85 AJT400 A070URD33XXX0630
MCD5-0380C 380 85 85 AJT450 A070URD33XXX0700
MCD5-0425B 430 85 85 AJT450 A070URD33XXX0700
MCD5-0595C 620 85 85 A4BQ800 A070URD33XXX1000
MCD5-0619C 650 85 85 A4BQ800 A070URD33XXX1000
MCD5-0790C 790 85 85 A4BQ1200 070URD33XXX1400
MCD5-0927C 930 85 85 A4BQ1200 A070URD33XXX1400
MCD5-1200C 1200 100 100 A4BQ1600 A065URD33XXX1800
MCD5-1410C 1410 100 100 A4BQ2000 A055URD33XXX2250
MCD5-1600C 1600 100 100 A4BQ2500 A055URD33XXX2250
Electrical Installation MCD 500 Operating Instruction
26 MG.17.K3.02 - VLT
®
is a registered Danfoss trademark
44
- Operating Instructions 1
- MG.17.K3.02 - VLT 2
- 5 Application Examples 3
- 6 Operation 3
- 7 Programming 4
- 9 Troubleshooting 5
- 10 Specifications 5
- 1 Safety 6
- 2 Introduction 7
- 177HA382.11 8
- 3 Installation 9
- 177HA514.10 10
- 4 Electrical Installation 11
- 4.1.3 Remote Inputs 12
- 4.1.4 Serial Communication 12
- 4.1.5 Earth Terminal 12
- 177HA542.11 13
- 4.1.7 Motor Connection 14
- 4.2 In-Line Installation 14
- 177 HA4 31.11 15
- 177HA500.11 16
- 4.4 Current Ratings 17
- Start Time (seconds) 19
- Starts Per Hour 19
- 4.6 Bypass Contactor 22
- 4.7 Main Contactor 22
- 4.8 Circuit Breaker 22
- 4.9 Power Factor Correction 22
- 4.10 Fuses 23
- 4.10.1 Power Supply Fuses 23
- 4.10.4 Ferraz Fuses - HSJ 25
- 4.11 Schematic Diagrams 28
- 177HA426.11 29
- 5.3 Starting Modes 31
- 5.3.1 Constant Current 31
- 5.3.2 Current Ramp 31
- Voltage (% full voltage) 32
- 177HA511.10 33
- 5.6 Inside Delta Operation 34
- 5.7 Typical Start Currents 34
- 177HA522.10 36
- 177HA523.10 37
- 5.10 Emergency Run Operation 38
- 5.11 Auxiliary Trip Circuit 39
- 5.12 Soft Braking 40
- 5.13 Two Speed Motor 41
- 6.2 Control Methods 44
- 6.3 Local Control Buttons 44
- 6.4.8 Date and Time (S8) 46
- 6.4.9 SCR Conduction Bargraph 46
- 6.4.10 Performance Graphs 46
- 7.2 Quick Menu 48
- 7.2.1 Quick Setup 48
- 7.2.2 Application Setups 49
- 7.2.3 Loggings 50
- 7.3 Main Menu 50
- 7.3.1 Parameters 50
- 7.3.2 Parameter Shortcut 50
- 7.3.3 Parameter List 51
- 7.4 Primary Motor Settings 52
- 7.4.1 Brake 53
- 7.5 Protection 53
- 7.5.1 Current Imbalance 53
- 7.5.2 Undercurrent 53
- 7.5.4 Frequency Trip 54
- 7.6 Inputs 54
- * [00:00 - 30:00 55
- 7.7 Outputs 56
- 7.7.1 Relay A Delays 56
- 7.7.2 Relays B and C 56
- 7.7.4 Motor Temperature Flag 57
- 7.7.5 Analog Output A 57
- 7.8 Start/Stop Timers 57
- 7.9 Auto-Reset 58
- 7.9.1 Auto-Reset Delay 58
- 7.10 Secondary Motor Set 58
- 7.11 Display 60
- 7.11.2 Performance Graphs 61
- 7.12 Restricted Parameters 61
- * [100 - 2000 62
- 8.1 Set Date and Time 63
- 8.2 Load/Save Settings 63
- 8.3 Reset Thermal Model 63
- 8.4 Protection Simulation 63
- 8.5 Output Signal Simulation 64
- 8.6 Digital I/O State 64
- 8.7 Temp Sensors State 64
- 8.8 Alarm Log 64
- 8.8.1 Trip Log 64
- 8.8.2 Event Log 65
- 8.8.3 Counters 65
- 9.2 General Faults 69
- Symptom Probable Cause 70
- 10.1 Accessories 72
- 10.1.1 Communication Modules 72
- 10.1.2 PC Software 73
- 10.1.3 Finger Guard Kit 73
- *MG17K302* 77
Related products and manuals for Circular saws Delta 28-299A
Circular saws Delta 36-5000 Instruction Manual
(100 pages)
(100 pages)
Circular saws Delta 20-140 User Manual
(8 pages)
Circular saws Delta 36-648 User Manual
(12 pages)
(12 pages)
Circular saws Delta 36-600 User Manual
(15 pages)
(15 pages)
Circular saws Delta MS210 User Manual
(35 pages)
(35 pages)
Circular saws Delta 36-075 User Manual
(28 pages)
(28 pages)
Circular saws Delta 20-140 User Manual
(5 pages)
(5 pages)
© 2020, manymanuals.com. All rights reserved. | 1.948 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals