Delta MMC120 User Manual Page 4
- Page / 150
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
4
The command deceleration is invalid................................................................................................... 77
Both sync bits cannot be set in the "Mode" word.................................................................................. 77
One or more synced axes are uninitialized........................................................................................... 77
Incompatible sync mode words............................................................................................................ 77
"Event Step Edit" indices are invalid................................................................................................... 77
Unknown Parameter Error.................................................................................................................. 78
APPENDIX A: COMMAND REFERENCE........................................................................................ 78
G
ENERAL ASCII COMMANDS .................................................................................................................. 78
Change Acceleration Command.......................................................................................................... 78
Change Deceleration Command.......................................................................................................... 78
Start Events Command........................................................................................................................ 79
Set Feed Forward Command............................................................................................................... 79
Go Command...................................................................................................................................... 79
Halt Command ................................................................................................................................... 80
Set Integral Drive Command............................................................................................................... 80
Set Integral Drive to Null Drive Command.......................................................................................... 81
Relative Move Command .................................................................................................................... 81
Disable Drive Output Command ......................................................................................................... 81
Set Mode Command............................................................................................................................ 82
Set Null Drive Command..................................................................................................................... 82
Set Null Drive to Integral Drive Command.......................................................................................... 82
Open Loop Command ......................................................................................................................... 82
Set Parameters Command................................................................................................................... 84
Quit Events Command ........................................................................................................................ 84
Restore Null Drive Command.............................................................................................................. 84
Restore Integral Drive Command........................................................................................................ 84
Save Null Drive Command.................................................................................................................. 85
Save Integral Drive Command ............................................................................................................ 85
Update FLASH Command................................................................................................................... 85
Set Speed (Unsigned) Command.......................................................................................................... 86
Set Speed (Signed) Command.............................................................................................................. 86
Start a Graph Command..................................................................................................................... 86
P
ROGRAMMABLE CONTROLLER COMMANDS ............................................................................................ 87
Go Using Profile Commands............................................................................................................... 87
Set Profile Commands......................................................................................................................... 88
Set Parameter Commands................................................................................................................... 90
ASCII Commands ............................................................................................................................... 91
Open Loop Using Profile Commands .................................................................................................. 91
Get Profile Commands........................................................................................................................ 93
Get Parameter Commands.................................................................................................................. 95
Event Step Edit Commands ................................................................................................................. 97
LINK TYPE/NEXT.............................................................................................................................. 98
Diagnostics Command........................................................................................................................ 98
Event Step Transfer Command............................................................................................................ 99
APPENDIX B: COMMAND FIELD REFERENCE ......................................................................... 101
MODE ................................................................................................................................................. 101
MODE W
ORD BIT MAP......................................................................................................................... 103
ACCELERATION................................................................................................................................ 104
DECELERATION................................................................................................................................ 104
SPEED ................................................................................................................................................. 105
COMMAND VALUE........................................................................................................................... 105
C
OMMAND FIELD .................................................................................................................................. 106
APPENDIX C: PARAMETER FIELD REFERENCE...................................................................... 106
- DCS120-Win Software 1
- User Manual 1
- Table of Contents 2
- Introducing the MMC120 7
- MMC120 Overview 7
- Disclaimer 7
- Principle of Operation 9
- Starting Up the MMC120 11
- Step-by-Step MMC120 Startup 11
- Setup Details 15
- Using DCS120-Win 20
- DCS120-Win Overview 20
- Screen Layout 21
- Command area 22
- Parameter area 23
- Plot Time area 24
- Status area 24
- Status Bar 24
- Basic Topics 26
- Read-back versus Write Mode 27
- Using Popup Editors 28
- Using the STATUS Bits Window 28
- Using the Command Log 29
- Using Stored Commands 31
- Setup Options 32
- Using Multiple Motion Modules 33
- Creating a New Board File 33
- Changing Between Board Files 34
- Using Plots 37
- Selecting the Data to Plot 38
- Using the Plot Detail Window 38
- Viewing the Raw Plot Data 39
- Saving and Restoring Plots 40
- Printing a Plot 40
- Plot Time 41
- Table Editors 42
- Editing the Profile Table 44
- Editing the Event Step Table 44
- Advanced Topics 47
- Forcing Initialization 48
- Using Look-only Mode 48
- Using PC Mode 48
- Command Line Options 49
- Options Dialog Box 50
- Controller Features 51
- Event Control Overview 51
- FLASH Memory 53
- LED Indicators 54
- Motion Profiles 55
- Synchronizing Axes 57
- Two per unit 60
- Communicating with the MMC120 61
- Input Register Overview 63
- Output Register Overview 64
- 1514131211109876543210 65
- SAR Type Index 65
- Support and Troubleshooting 66
- Warranty 66
- Troubleshooting 66
- Error Handling 67
- MMC120 Module Problems 67
- Hydraulic System Problems 69
- Technical Support 73
- Parameter Errors 74
- Invalid command received 76
- Appendix A: Command Reference 78
- General ASCII Commands 78
- Start Events Command 79
- Set Feed Forward Command 79
- Go Command 79
- Halt Command 80
- Set Integral Drive Command 80
- Relative Move Command 81
- Disable Drive Output Command 81
- Set Mode Command 82
- Set Null Drive Command 82
- Open Loop Command 82
- Set Parameters Command 84
- Quit Events Command 84
- Restore Null Drive Command 84
- Save Null Drive Command 85
- Save Integral Drive Command 85
- Update FLASH Command 85
- Set Speed (Unsigned) Command 86
- Set Speed (Signed) Command 86
- Start a Graph Command 86
- Go Using Profile Commands 87
- Set Profile Commands 88
- Set Parameter Commands 90
- ASCII Commands 91
- Get Profile Commands 93
- 0xAC-0xAF 37 94
- Get Parameter Commands 95
- Event Step Edit Commands 97
- LINK TYPE/NEXT 98
- Diagnostics Command 98
- Event Step Transfer Command 99
- MODE Word Bit Map 103
- ACCELERATION 104
- DECELERATION 104
- COMMAND VALUE 105
- Command Field 106
- CONFIGURATION Word 107
- CONFIGURATION Word Bit Map 109
- SCALE Calculation Examples 111
- EXTEND LIMIT 112
- RETRACT LIMIT 113
- PROPORTIONAL GAIN 113
- INTEGRAL GAIN 114
- DIFFERENTIAL GAIN 115
- EXTEND FEED FORWARD 115
- RETRACT FEED FORWARD 116
- DEAD BAND ELIMINATOR 117
- IN POSITION 118
- FOLLOWING ERROR 118
- AUTO STOP 119
- AUTO STOP Bit Map 120
- Valid 16-Bit Positions 121
- COMMAND POSITION 122
- TARGET POSITION 123
- ACTUAL POSITION 123
- TRANSDUCER COUNTS 124
- AXIS STATUS Word 124
- STATUS Word Bit Map 128
- ACTUAL SPEED 129
- NULL DRIVE 130
- LINK VALUE 130
- Link Types and Link Values 130
- Link Next 131
- System-wide Link Types 132
- Current Axis Link Types 132
- Link Type and Link Value 133
- Selected Axis Link Types 135
- Link Type - Any Axis Speed 136
- MMC120 Specifications 138
- Appendix G: Glossary 139
- Glossary 139
Related products and manuals for Sensors Delta MMC120
Sensors Delta MMC120 User Manual
(105 pages)
(105 pages)
© 2020, manymanuals.com. All rights reserved. | 1.834 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals