Delta 23-710 Instruction Manual Page 6
- Page / 64
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
6
EXTENSION CORDS
Use proper extension cords. Make
sure your extension cord is in good condition and
is a 3-wire extension cord which has a 3-prong
grounding type plug and matching receptacle which
will accept the machine’s plug. When using an
extension cord, be sure to use one heavy enough to
carry the current of the machine. An undersized cord
will cause a drop in line voltage, resulting in loss
of power and overheating. Fig. D-1 or D-2, shows
the correct gauge to use depending on the cord
length. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord.
Fig. D-1
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere
Rating Volts
Total
Length of
Cord in
Feet
Gauge of Extension
Cord
0-6 120
up to
25 18 AWG
0-6 120 25-50 16 AWG
0-6 120 50-100 16 AWG
0-6 120 100-150 14 AWG
6-10 120
up to
25 18 AWG
6-10 120 25-50 16 AWG
6-10 120 50-100 14 AWG
6-10 120 100-150 12 AWG
10-12 120
up to
25 16 AWG
10-12 120 25-50 16 AWG
10-12 120 50-100 14 AWG
10-12 120 100-150 12 AWG
12-16 120
up to
25 14 AWG
12-16 120 25-50 12 AWG
12-16 120
GREATER THAN 50 FEET NOT RECOMMENDED
FOREWORD
FUNCTIONAL DESCRIPTION
NOTICE: The manual cover illustrates the current production model. All other illustrations contained in the manual are
representative only and may not depict the actual labeling or accessories included. These are intended to illustrate
technique only.
CARTON CONTENTS
The Delta Industrial Sharpening Center Model 23-710 has a 1/5 HP motor. It also comes with a 5” diameter, 120 grit
aluminum oxide dry wheel, an 8” diameter, 1000-grit wet wheel, a tool rest and base, a sliding tool holder, a water tank,
eye shield and wrenches.
2
1. Sharpening Center
2. Water Tank
3. Tool and Chisel Holder
4. Wheel Dressing Stone
5. Tool and Chisel Holder Base
Assembly
6. Tilting Screw and Spring for
Tool and Chisel Holder w/
(2) Flat Washers
7. 6mm Allen wrench
8. 6mm Allen Wrench
9. Wrench
10. Tool Rest for Dry Wheel
11. Flat Washer
12. Lockwasher
13. 5/8” Long Hex Head Screw
14. Eyeshield Clamp Bracket
15. Eyeshield Mounting Rod
16. Eyeshield Lock Knob
17. 3/4” Long Carriage Head Bolt
18. 1/4-20 Hex Nut
19. Eyeshield Frame
20. 1/2” Long, Round Head Screw
(2)
21. Flat Washer (2)
22. #10-24 Hex Nut (2)
23. Eyeshield
1
8
9
3
4
13
12
11
10
14
15
16
17
18
23
22
19
20
21
5
7
6
- Instruction Manual 1
- Manuel d’utilisation 1
- Manual de instrucciones 1
- IMPORTANT SAFETY INSTRUCTIONS 2
- TABLE OF CONTENTS 2
- GENERAL SAFETY RULES 3
- SAVE THESE INSTRUCTIONS 4
- POWER CONNECTIONS 5
- MOTOR SPECIFICATIONS 5
- GROUNDING INSTRUCTIONS 5
- FUNCTIONAL DESCRIPTION 6
- CARTON CONTENTS 6
- ASSEMBLY 7
- ASSEMBLING AND 8
- ADJUSTING TOOL REST 8
- FOR DRY WHEEL 8
- WRENCH HOLDING BRACKET 8
- ASSEMBLING AND ADJUSTING 9
- TOOL AND CHISEL HOLDER 9
- OPERATION 12
- TOOL REST ON DRY WHEEL 16
- ER OR JOINTER KNIVES 17
- REPLACING WET GRINDING WHEEL 19
- REPLACING DRY GRINDING WHEEL 19
- TROUBLESHOOTING 20
- MAINTENANCE 20
- ACCESSORIES 21
- WARRANTY 21
- RÈGLES DE SÉCURITÉ GÉNÉRALES 23
- CONSERVER CES DIRECTIVES 24
- Les consulter souvent 24
- RACCORDEMENTS ÉLECTRIQUES 25
- SPÉCIFICATIONS DU MOTEUR 25
- DESCRIPTION FONCTIONNELLE 26
- CONTENUS DE BOITE 26
- ASSEMBLAGE 27
- OUTIL POUR MEULAGE À SEC 28
- SUPPORT DE CLÉ 28
- OUTIL ET PORTE-BÉDANE 29
- SURFACE PORTANTE 31
- FONCTIONNEMENT 32
- MEULE À EAU 34
- MEULE SÈCHE 36
- RABOTEUSES 37
- REMPLACEMENT D’UNE 39
- REMPLACEMENT DE LA 39
- MEULE À SEC 39
- ENTRETIEN 40
- DEPANNAGE 40
- ACCESSOIRIES 41
- GARANTIE 41
- NORMAS GENERALES DE SEGURIDAD 43
- ESPECIFICACIONES DEL MOTOR 45
- DESCRIPCIÓN FUNCIONAL 46
- CONTENIDO DE CARTON 46
- ENSAMBLAJE 47
- ENSAMBLAJE Y AJUSTE DEL 48
- SOPORTE DE HERRAMIENTAS PARA 48
- DISCO PARA ESMERILAR EN SECO 48
- SOPORTE DE SUJECIÓN DE LA 48
- SUJETADOR DE HERRAMIENTAS Y 49
- OPERACIÓN 52
- USO DEL SOPORTE DE 56
- HERRAMIENTAS DESLIZANTE 56
- PARA ESMERILAR EN SECO 56
- USO DEL SOPORTE DE HERRAMIEN 57
- TAS CON CUCHILLAS DE CEPILLA 57
- DORAS O EMPALMADORAS 57
- REEMPLAZO DEL DISCO PARA 59
- ESMERILAR EN HÚMEDO 59
- MERILAR EN SECO 59
- MANTENIMIENTO 60
- LOCALIZACION DE FALLAS 60
- SERVICIO 61
- ACCESORIOS 61
- PÓLIZA DE GARANTÍA 61
- por favor llame al 62
- (888) 848-5175 62
- ESPECIFICACIONES 62
- GARANTIA 63
- Delta Machinery 64
- 4825 Highway 45 North 64
- Jackson, TN 38305 64
- (800) 223-7278 64
Related products and manuals for Power tools Delta 23-710
Power tools Delta DP350 Instruction Manual
(17 pages)
(17 pages)
Power tools Delta BS150LS Instruction Manual
(25 pages)
(25 pages)
Power tools Delta 50-760 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 23-710 Instruction Manual
(24 pages)
(24 pages)
Power tools Delta 36-979 Instruction Manual
(17 pages)
(17 pages)
Power tools Delta 33-892 Instruction Manual
(28 pages)
(28 pages)
Power tools Delta 28-206 Instruction Manual
(24 pages)
(24 pages)
Power tools Delta 50-860 Specifications
(12 pages)
(12 pages)
Power tools Delta 11-985 Instruction Manual
(16 pages)
(16 pages)
Power tools Delta 23-700 Instruction Manual
(10 pages)
(10 pages)
Power tools Delta 23-725 Instruction Manual
(20 pages)
(20 pages)
Power tools Delta DJ-15 Instruction Manual
(24 pages)
(24 pages)
Power tools Delta 36-714B Instruction Manual
(76 pages)
(76 pages)
Power tools Delta 37-071 Instruction Manual
(56 pages)
(56 pages)
Power tools Delta 23-710 User Manual
(6 pages)
(6 pages)
Power tools Delta 23-665 Instruction Manual
(10 pages)
(10 pages)
Power tools Delta N028314 Instruction Manual
(88 pages)
(88 pages)
Power tools Delta 50-861 Instruction Manual
(16 pages)
(16 pages)
© 2020, manymanuals.com. All rights reserved. | 0.852 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals